Any possibility your supplier is panel plating or flash plating before
pattern plate???? This also sounds sort of like what one used to get with
panel plate where the plating thickness varies across the board. I believe
there are still some quick turn shops panel plating.
----------
From: [log in to unmask]
To: [log in to unmask]
Subject: FWD>FAB- Etchback (PB Etchi
Date: Friday, July 26, 1996 12:51PM
Mail*Link(r) SMTP FWD>FAB: Etchback (PB Etching
Characteristics)
Date: 7/26/96 8:51 AM
From: JIM ENNIS
Hi Jim,
In response to your question, IMO your concern is not "etchback" in the
normal
terminology, rather your concern is "etching characteristics". The
following
comments are based on our 30+ years of experience for "etching" printed
boards
and performing photochemical machining of all types of metals and metal
alloys.
>We are having a significant problem with quickturn cards coming in
>overetched, and we're trying to understand some things about the process
of>etching.
>One question that has come up is: Is it possible for etching to be
>greater in one area of the card over another?
Yep -- you bet, even though the etching characteristics of spray etchers
have
come a long way over the years. There are a number of factors, such as
impact
spray pressure (not nozzle pressure), stratification/puddling of the
etchant,
conductor spacing, spray impingment angle, etchant (type, operating,
temperature, concentration, wetting factors), and spray agitation to
identify
a few.
When you have closely and widely spaced features (conductor spacings) the
closer spacings are preferentially etched faster due to etchant turbulence.
With close spacings, you have minimum "laminar" film fluid effects at the
interface between the etchant and the metal to be removed -- that is you
have
"turbulent" solution exchange. In larger areas, the etchant will tend to
become more "laminar" in fluid (etchant) flow, it becomes more saturated at
the interface layer and the etching rate is reduced. That's why all of the
above mentioned paramaters need to be characterized and controlled.
When you get down to less than about 100 micrometers (0.004 inch), in
particular in the range of 13-50 micrometers (0.0005-0.002 inch) the
viscosity, wetting factors, and gas generation of the etchant becomes
significantly more critical because the etchant becomes stagnant.
Some manufacturer's of etching equipment have somewhat optimized the design
of
their etching equipment to improve the etching equipments performance.
>If so, how is this possible, and what are the design considerations for
this?
That is why in the IPC's-D-275 it is "suggested/recommended" that the
designer
minimize the areas of "close/minimal" conductor spacings and spread the
conductors out when ever possible. Because, IMO, the majority of us are
stuck
with CAD systems with an IQ that is barely measurable, the automated design
systems route to minimum in an x or y orientation and most systems do not
"automatically" spreadout closely spaced conductors, when possible, on a
routine basis. Instead, most CAD designers/operators must manually edit the
conductive patterns --- labor intensive and time consuming, and it's seldom
done in today's fast-lane paced work environment. [Comment -- oh!
Ralllllphoooo - are you going to stimulate comments from the CAD community
with those comments].
The key is to do what you can as a DfM (design for manufacturability) and
then
find a printed board manufacturer who has characterized and controls their
processes and that will meet your requirements.
Sometimes finding a PB manufacturer that uses a different etchant will help,
because all etchants don't etch the same, even within the same family of
etchant.
>Some here contend that every feature should etch down by the same >nominal
amount, say .002 inch, whether the feature is an .008 trace or a >large
ground plane, since the whole PCB is exposed to etchant at the same >time.
Is there fault in this thinking?
In theory (sometimes in practice) this is true, provided you identify,
characterized and control the 10-50 variables.
>Thanks in advance.
>Jim Ennis
>Adtran Inc
>[log in to unmask]
Hope this helps
Ralph Hersey
e-mail [log in to unmask]
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
------------------ RFC822 Header Follows ------------------
Received: by quickmail.llnl.gov with SMTP;26 Jul 1996 08:50:13 -0700
Received: from ipc.org by simon.ipc.org via SMTP
(940816.SGI.8.6.9/940406.SGI)
id KAA14798; Fri, 26 Jul 1996 10:42:48 -0700
Resent-Date: Fri, 26 Jul 1996 10:42:48 -0700
Received: by ipc.org (Smail3.1.28.1 #2)
id m0ujnpv-0000RdC; Fri, 26 Jul 96 09:25 CDT
Resent-Sender: [log in to unmask]
Old-Return-Path: <[log in to unmask]>
From: JIM ENNIS <[log in to unmask]>
To: TechNet <[log in to unmask]>
Subject: FAB: Etchback
Date: Fri, 26 Jul 96 09:35:00 PDT
Message-Id: <[log in to unmask]>
Encoding: 16 TEXT
X-Mailer: Microsoft Mail V3.0
Resent-Message-ID: <"yCaYW2.0.jAC.SLD-n"@ipc>
Resent-From: [log in to unmask]
X-Mailing-List: <[log in to unmask]> archive/latest/5362
X-Loop: [log in to unmask]
Precedence: list
Resent-Sender: [log in to unmask]
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
|