Received: |
by ipc.org (Smail3.1.28.1 #2)
id m0vUaSE-0000SOC; Mon, 2 Dec 96 09:38 CST |
Encoding: |
55 Text |
Old-Return-Path: |
<simon.ipc.org!uunet.uu.net!esseye!smtpgwy.si.com!Juanita_Zeinstra_at_sia-gr6> |
Date: |
Mon, 02 Dec 96 09:17:55 EST |
Precedence: |
list |
Resent-From: |
|
From [log in to unmask] Tue Dec 3 14: |
46:03 1996 |
Resent-Sender: |
|
X-Status: |
|
Status: |
O |
X-Mailing-List: |
|
TO: |
|
Return-Path: |
<TechNet-request> |
Resent-Message-ID: |
<"26lEu3.0.r-I.UVleo"@ipc> |
Subject: |
|
From: |
|
X-Loop: |
|
Message-Id: |
|
Parts/Attachments: |
|
|
why not Mentor? - there is movement to a PC platform. It is the only
vendor that is still in tact after our survey for PCB tools 10 years
ago. The others have merged, sold, re-sold, etc.
______________________________ Reply Separator _________________________________
Subject: PCB Design S/W - Soliciting Inputs
Author: [log in to unmask] at SMTPpost1
Date: 11/26/96 1:25 PM
We are in the beginning stages of trying to decide what PCB design
software to migrate to. We are finding that our current systems which are
PADS Logic, Power PCB, Cadkey & Gerbtool just isn't going to get the job
done in the near future. The three systems that we have knowledge with &
that we believe will do the job that we envision being required are
Cadence, Zuken-Redac's Visula & Intergraph. We want a platform that will
run on Window's NT with Pentium based hardware. We currently have 90Mhz
Pentiums with 32 to 64 Meg of ram on each.
I have experience with trying to get Cadence into a facility but would
like to hear from others in the feild. What I'm looking for is good
and/or bad experiences with each platform.
Information from the representatives from these three vendors would be
greatly apreciated. What we are looking for from a package is
exceptional mechanical drawing capablilities (for doing the Fabrication
drawing & Panelization drawing) with good GD&T utilization as well as
ability to handle robust PCB design rules, checking, layout, Digital &
analog design simulation. We also want to have Gerber 274X file
manipulation as a standard feature to veiw and panelize A/W. We require
real time back anotation. Also outputs for driving our automatic Pick &
Place equipment.
I don't think I'm looking for a dream system here and I know that
whatever we end up with will be a hybrid of what we at this point
envision so any input will be greatly apreciated.
Thanks in advance;
Steve Collins
PCB Design Supervisor
TSX Corporation
El Paso, TX
Ph: (800) 351-2345
Fax: (915) 543-4898
email: [log in to unmask]
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
|
|
|