...PCB fabrication will not be a problem ??
How does your PWB fab vendor propose to plate these holes [reliably]?
If there are "no external layer traces or connections...", isn't it a
blind via?
Anyway, this is very difficult to do, depending on the hole size...
FABRICATION:
In conventional outerlayer imaging, the circuitry and pads are
built concurrently with the PTH thickness. Consistent, voidless
plating demands (among other things) hydrodynamic chemistry
replenishment inside the holes, usually accomplished through
perpendicular agitation. Without agitation (or with a hole closed on
one side) the panel movement cannot easily 'flush' fresh solution
through the hole. To plate the PTV with only one pad requires
shrinking the imaged (photoresist) hole on the non-pad side to smaller
than the hole diameter (since artwork-to-drill pattern registration is
never perfect) thus partially tenting the hole and inviting solution
stagnation during Cu plating.
RELIABILITY:
The weak point will be introduced at the 'knee' where the
photoresist is draped over the hole wall and partially into the hole.
Fresh plating solution will have a tough time getting to this
interface with the outerlayer copper foil (is it half oz or 1 oz?).
If resist lam/expose/developing conditions were not ideal, the
potential for a rim void will exist at the top of the hole. Even if
there is no circuitry connected to the outerlayer pad, partially
choking off the hole may cause voids at innerlayer connections. With
pads on both sides of a PTV, you get a two-point connection to the O/L
copper foil, kind'a like a rivet. With one pad removed, you end up
with a circumferential connection limited to the thickness of the O/L
foil. On a .093" 14L, you undoubtedly have a high resin-to-glass
ratio, thus high thermal expansion at solder temperatures (and high
stress concentration on the barrel copper); this is what fractures
high-aspect ratio, weakly-plated vias.
SUGGESTION:
Drop the hole size (I'm assuming they're vias) down to a #77
(.018") or even #80 (.0135"), and the pads down to .025"-.030"
diameter, but for long-term reliability - keep the pads. [Please call
or e-mail if you're interested in further discussion].
ON THE OTHER HAND...
I invite further discussion from PWB fab shops on how padless vias
can be reliably made; it might be of some interest for producing
blind and buried, sequentially-laminated vias...
Joe Felts
PC World, Toronto
(416) 299-4000
[log in to unmask]
______________________________ Reply Separator _________________________________
Subject: ASSY - Padless Plated Thru Holes
Author: [log in to unmask] at INET
Date: 11/13/96 8:37 AM
--openmail-part-04e010ac-00000002
Content-Type: text/plain; charset=US-ASCII; name="ASSY"
Content-Transfer-Encoding: quoted-printable
To extend clearance and eliminate potential shorts to the bottom
of a connector, the component side pad must be reduced to zero.
In other words,a top side padless PTH. The shorts are occuring during
wave solder.
What reliability down sides can we expect? Im advised that PCB
fabrication will not be a problem. Im mostly concerned with assembly
and repair operations.
Parameters: .093", 14 layer board
Finished hole .033" with solder side pad at .060"
No external layer traces or connections.
All connections are internal planes.
Thanks in advance: Ed Cassinelli =
Stratus Computer Inc
508-490-6821
--openmail-part-04e010ac-00000002
Content-Type: application/rtf; name="ASSY"
Content-Transfer-Encoding: base64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--openmail-part-04e010ac-00000002--
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
|