 
| X400-Content-Type: |
P2-1988 ( 22 ) |
| Old-Return-Path: |
|
| Date: |
14 Aug 96 08:13:48 -0500 |
| Precedence: |
list |
| Resent-From: |
|
| Conversion: |
Allowed |
| From [log in to unmask] Wed Aug 14 08: |
20:53 1996 |
| Resent-Sender: |
|
| X-Status: |
|
| Status: |
O |
| Priority: |
non-urgent |
| X-Loop: |
|
| Content-Return: |
Allowed |
| X-Mailing-List: |
|
| TO: |
|
| Received: |
by ipc.org (Smail3.1.28.1 #2)
id m0uqfmV-0000MrC; Wed, 14 Aug 96 08:14 CDT |
| Return-Path: |
<TechNet-request> |
| X400-Originator: |
|
| X400-Recipients: |
non-disclosure; |
| Alternate-Recipient: |
Allowed |
| Message-Id: |
<02F803211D10C001*/c=us/admd=cwmail/prmd=carrier/o=syracuse/ou=ccmail1/s=Parr/g=Aric/@MHS> |
| Resent-Message-ID: |
<"ALqCP3.0.n-B.25T4o"@ipc> |
| Subject: |
|
| From: |
|
| Disclose-Recipients: |
Prohibited |
| X400-Received: |
by /c=us/admd=cwmail/; Relayed; 14 Aug 96 08:13:48 -0500
by mta MTAwltk in /c=us/admd=cwmail/; Relayed;
14 Aug 96 08:13:48 -0500 |
| Content-Identifier: |
02F803211D10C001 |
| X400-Mts-Identifier: |
[/c=us/admd=cwmail/; 02F803211D10C001-MTAwltk] |
| Parts/Attachments: |
|
|
We found mixed results using Glicoat, a competing material made in
Japan.
We have mixed results on yield, with no change to 100% fallout
depending upon PCB design, number of thermal cycles and nitrogen
level, if any on both reflow, wave or both.
We also found cost savings at some PCB suppliers with organic coats,
and cost increases from others.
[log in to unmask]
______________________________ Reply Separator _________________________________
Subject: Re: ASSY: Entek Coating
Author: [log in to unmask] at internet
Date: 8/12/96 5:52 PM
Hello Larry,
I've taken the liberty of giving your name to Scot Burns of
Enthone.OMI. He has agreed to call you. He has also suggested that I
give you his number, as well.
His number is: 1.619.743.4061.
[log in to unmask]
The views stated above are not necessarily those of my employer.
______________________________ Reply Separator _________________________________
Subject: ASSY: Entek Coating
Author: [log in to unmask] at internet
Date: 8/12/96 1:29 PM
Hello:
I am a PCB designer that also get PCB's fabricated. We have been approached
by one of our vendors about calling out Entek coating instead of HASL. Our
customers range from soldering the parts on at their bench to sending them
out to be stuffed. My question is: What are the pros and cons when
assembling thru-hole and SMT parts with this Entek coating on the board?
Thanks in advance.
Larry L. Pucket
Dept. 9784 MS0624
Sandia National Laboratories
P.O. Box 5800
Albuquerque, NM 87185-0624
Phone: (505)844-1711
Fax: (505)844-7428
Email: [log in to unmask]
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
***************************************************************************
* TechNet mail list is provided as a service by IPC using SmartList v3.05 *
***************************************************************************
* To unsubscribe from this list at any time, send a message to: *
* [log in to unmask] with <subject: unsubscribe> and no text. *
***************************************************************************
|
|
|
