Subject: | |
From: | |
Reply To: | |
Date: | Wed, 13 Apr 2016 13:51:10 +0000 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Pietro,
Circuit Medic works well for simple wire fastening. Typically for 30 or 26 AWG "rework" wire.
http://www.circuitmedic.com/products/310-2100.shtml
Phil
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Roger Mack
Sent: Wednesday, April 13, 2016 9:48 AM
To: [log in to unmask]
Subject: Re: [TN] adhesive recommendation
Environment does matter. If you are using in harsh or automotive
environment, test the different options in temperature cycle testing. You
will likely find the CA glues will fail. Some use an RTV. You should also
consider tape dots. We found they exceeded the temp cycling requirements
and do not have any curing to worry about. Look up wire dots from
circuitmedic for example. We have used these for many years with no
issues.
Roger Mack P.Eng.
Manufacturing Specialist
Parker Hannifin Canada
Electronic Controls Division
1305 Clarence Avenue
Winnipeg, MB R3T 1T4 Canada
direct 204 453 3339 x7373
[log in to unmask]
www.parker.com/ecd
From: "Stadem, Richard D." <[log in to unmask]>
To: <[log in to unmask]>
Date: 2016-04-13 08:30 AM
Subject: Re: [TN] adhesive recommendation
Sent by: TechNet <[log in to unmask]>
It depends on the product type. Can you give us a little more info as to
what the product is and its typical use environment? Also, is the board
conformal coated?
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of pietro
Sent: Wednesday, April 13, 2016 7:49 AM
To: [log in to unmask]
Subject: [TN] adhesive recommendation
Hi.
I'm new to the forum and hope my request make sense.
When using jumper wires on PCB, besides other directives IPC recommend to
put adhesive spot at least every 25.4mm.
My basic question: is there any recommendation about what kind of
glue/adhesive to use ?
Any suggestion will help.
Thanks
Pietro
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
--
Pietro Vergine
President
CID Trainer
Leading Edge
Via Delle Attivitá 18
24041 Brembate (Bergamo) - Italy
mobile (+39) 335-5783220
email: [log in to unmask]
internet: www.leading-edge.it
Skype: pietver27
Rispetta l'ambiente: se non ti è necessario, non stampare questa mail.
To respect the environment, if not necessary do not print this email
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
|
|