working on mm wave bands? 19 GHz?
jk
> Nope. Clawed my way up from RF R&D tech back in the late 70's.
>
> Ed Popielarski
> Engineering Manager
>
>
> 970 NE 21st Ct.
> Oak Harbor, Wa. 98277
>
> Ph: 360-675-1322
> Fx: 206-624-0695
> Cl: 949-581-6601
>
>
>
> "It's one kind of victory to slay a beast, move a mountain, and
> cross a chasm, but it's another kind altogether to realize that the
> beast, the mountain, and the chasm were of your own design."
> https://maps.google.com/maps/myplaces?hl=en&ll=48.315753,-122.643578&spn=0.011188,0.033023&ctz=420&t=m&z=16&iwloc=A
>
>
> -----Original Message-----
> From: [log in to unmask] [mailto:[log in to unmask]]
> Sent: Friday, October 02, 2015 8:50 AM
> To: TechNet E-Mail Forum; Ed Popielarski
> Subject: Re: [TN] Solder mask removal, SMOBC
>
> you mean you are the "pure manager" without the engineering part?
> LOL.
> jk
>> Hey now... I quit several months ago (and damned proud of it after 40+
>> years)... cut me a little slack, bud! LOL
>>
>> Ed Popielarski
>> Engineering Manager
>>
>>
>> 970 NE 21st Ct.
>> Oak Harbor, Wa. 98277
>>
>> Ph: 360-675-1322
>> Fx: 206-624-0695
>> Cl: 949-581-6601
>>
>>
>>
>> "It's one kind of victory to slay a beast, move a mountain, and
>> cross a chasm, but it's another kind altogether to realize that the
>> beast, the mountain, and the chasm were of your own design."
>> https://maps.google.com/maps/myplaces?hl=en&ll=48.315753,-122.643578&s
>> pn=0.011188,0.033023&ctz=420&t=m&z=16&iwloc=A
>>
>>
>> -----Original Message-----
>> From: Stadem, Richard D. [mailto:[log in to unmask]]
>> Sent: Friday, October 02, 2015 8:19 AM
>> To: Ed Popielarski; TechNet E-Mail Forum
>> Subject: RE: Solder mask removal, SMOBC
>>
>> Yes, and they would have the proper environmental controls and safety
>> equipment, etc.
>> Even if you attempted to remove it using a conformal coat blaster, you
>> still have the safety issues to deal with. You don't want to breathe
>> that stuff.
>> Excuse me while I go outside for a cigarette.
>> Odin
>>
>> -----Original Message-----
>> From: Ed Popielarski [mailto:[log in to unmask]]
>> Sent: Friday, October 02, 2015 10:16 AM
>> To: TechNet E-Mail Forum; Stadem, Richard D.
>> Subject: RE: Solder mask removal, SMOBC
>>
>> In addition to Richard's sage advice and rationalization is the fact
>> they are set up to deal with harsh chemistry like this and probably do
>> so on a regular basis.
>>
>> Ed Popielarski
>> Engineering Manager
>>
>>
>> 970 NE 21st Ct.
>> Oak Harbor, Wa. 98277
>>
>> Ph: 360-675-1322
>> Fx: 206-624-0695
>> Cl: 949-581-6601
>>
>>
>>
>> "It's one kind of victory to slay a beast, move a mountain, and
>> cross a chasm, but it's another kind altogether to realize that the
>> beast, the mountain, and the chasm were of your own design."
>> https://maps.google.com/maps/myplaces?hl=en&ll=48.315753,-122.643578&s
>> pn=0.011188,0.033023&ctz=420&t=m&z=16&iwloc=A
>>
>>
>> -----Original Message-----
>> From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard D.
>> Sent: Friday, October 02, 2015 5:36 AM
>> To: [log in to unmask]
>> Subject: Re: [TN] Solder mask removal, SMOBC
>>
>> Perhaps you can ask your board fabricator? I would imagine they have
>> methods for doing this. Perhaps also they may be able to do it for you
>> cheaper than you could set yourself up to do it? Doesn't hurt to ask.
>>
>> -----Original Message-----
>> From: TechNet [mailto:[log in to unmask]] On Behalf Of Victor Hernandez
>> Sent: Friday, October 02, 2015 6:52 AM
>> To: [log in to unmask]
>> Subject: [TN] FW: Solder mask removal, SMOBC
>>
>> Fellow TechNetters:
>>
>> I did not receive very much feedback on my initial inquiry.
>> Therefore, I ask again. Additionally I also ask if Solder mask and
>> conformal coating the same Product/Term (IPC-7711.21 section 2.3.1.
>> I want to removal/strip solder mask. At this point I do not known the
>> solder mask vendor or type.
>>
>> Victor,
>>
>> From: Hernandez, Victor G
>> Sent: Thursday, October 01, 2015 10:56 AM
>> To: TechNet E-Mail Forum
>> Cc: Hernandez, Victor G
>> Subject: Solder mask removal
>>
>> Fellow TechNetters:
>>
>> I have been asked to see if that is a satisfactory method for
>> removing/stripping solder mask from sample coupons chemically and/or
>> mechanically.
>>
>> Victor,
>>
>>
>> ______________________________________________________________________
>> This email has been scanned by the Symantec Email Security.cloud
>> service.
>> For more information please contact helpdesk at x2960 or
>> [log in to unmask]
>> ______________________________________________________________________
>>
>> ______________________________________________________________________
>> This email has been scanned by the Symantec Email Security.cloud
>> service.
>> For more information please contact helpdesk at x2960 or
>> [log in to unmask]
>> ______________________________________________________________________
>>
>> ______________________________________________________________________
>> This email has been scanned by the Symantec Email Security.cloud
>> service.
>> For more information please contact helpdesk at x2960 or
>> [log in to unmask]
>> ______________________________________________________________________
>>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or [log in to unmask]
> ______________________________________________________________________
>
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
