Steve,

Where's the "Like" icon?  That's great.

Chuck


Charles W. Brummer | 3M Manufacturing Engineer
3M Electronic Solutions Division
3M Canoga Park, 8357 Canoga Ave. | Canoga Park, CA 91304
Office: 818 734 4930
[log in to unmask] | www.3M.com


This message (including any attachments) may contain material, non-public 
information or proprietary information and is for the intended recipients 
only. If you are not the intended recipient, you should notify the sender 
and delete this message. Any disclosure, copying, or use of this 
information is strictly prohibited and may subject you to legal liability.



From:   "Steve Gregory" <[log in to unmask]>
To:     <[log in to unmask]>
Date:   05/12/2015 07:05 PM
Subject:        Re: [TN] Mirror tape
Sent by:        TechNet <[log in to unmask]>



Yeah, the reason that I thought of polishing stainless steel is because I
remembered about a beautiful 9,000-lb. stainless steel sculpture of a 
water
dragon that was done by a Canadian artist named Kevin Stone. He has over
2-miles of TIG welds in this thing:

http://alchemyimageworks.com/metal_dragon.jpg

Steve

On Tue, May 12, 2015 at 3:38 PM, Steve Gregory <[log in to unmask]> wrote:

> Hi again Ioan,
>
> I spent a little more time on that piece of stencil material (about
> 15-minutes) and it turned out pretty good:
>
> http://stevezeva.homestead.com/Stencil_Mirror_2.jpg
>
> Wound up giving it to one our final inspectors....
>
> Steve
>
> On Tue, May 12, 2015 at 2:24 PM, Steve Gregory <[log in to unmask]> 
wrote:
>
>> Hi Ioan!
>>
>> Hey why not make your own? I'm sure you have some old stencils laying
>> around, so just cut a piece out of one and take a Dremel tool and get 
one
>> of them fabric buffing wheels that usually come with them and some of 
that
>> brick red buffing compound in a stick that nobody ever uses, then buff
>> yourself up your own mirror. Here's a piece of stencil that I only 
spent a
>> few minutes on and it buffs up really reflective:
>>
>> http://stevezeva.homestead.com/Stencil_Mirror.jpg
>>
>> Steve
>>
>> On Tue, May 12, 2015 at 6:06 AM, Ioan Tempea <
>> [log in to unmask]> wrote:
>>
>>> Dear Technos,
>>>
>>> We need to inspect epoxy bonds of a few components placed about 0.010"
>>> away from a cavity wall, perpendicular to the wall. As direct view is 
not
>>> possible, I was thinking about using some sort of highly reflective 
tape or
>>> thin sheet metal, that we would slide between the wall and the 
terminations.
>>>
>>> Do you have any suggestions of such material?
>>>
>>> Thanks,
>>>
>>> Ioan Tempea, P. Eng.
>>> Manufacturing Engineer, Satellite Systems
>>>
>>> MacDonald, Dettwiler and Associates Corporation, 21025 Trans-Canada
>>> Highway, Ste-Anne-de-Bellevue, QC, Canada H9X 3R2
>>> Tel: +1-514-457-2150 x3556
>>> www.mdacorporation.com<http://www.mdacorporation.com/>
>>>
>>> This e-mail, and any attachments, are intended solely for the use of 
the
>>> intended recipient(s) and may contain legally privileged, proprietary
>>> and/or confidential information. Any use, disclosure, dissemination,
>>> distribution or copying of this e-mail and any attachments for any 
purposes
>>> that have not been specifically authorized by the sender is strictly
>>> prohibited. If you are not the intended recipient, please immediately
>>> notify the sender by reply e-mail and permanently delete all copies 
and
>>> attachments. This email is for informational purposes only and shall 
not be
>>> interpreted to authorize or conclude a binding agreement between MDA 
and
>>> any other party unless this email contains or is accompanied by an 
express
>>> written confirmation of MDA's intention to enter into a binding 
agreement,
>>> such confirmation shall only be provided by an authorized 
representative of
>>> MDA.
>>>
>>>
>>> ______________________________________________________________________
>>> This email has been scanned by the Symantec Email Security.cloud 
service.
>>> For more information please contact helpdesk at x2960 or
>>> [log in to unmask]
>>> ______________________________________________________________________
>>>
>>
>>
>

-- 


This email and any attachments are only for use by the intended 
recipient(s) and may contain legally privileged, confidential, proprietary 

or otherwise private information. Any unauthorized use, reproduction, 
dissemination, distribution or other disclosure of the contents of this 
e-mail or its attachments is strictly prohibited. If you have received 
this 
email in error, please notify the sender immediately and delete the 
original. 


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________
3M security scanners have not detected any malicious content in this 
message.

To report this email as SPAM, please forward it to [log in to unmask]



______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________