Wow, if they are microvias on a grid pattern, that would be the first time
I've ever seen that. I can't even wrap my head around how many holes that
board would have!
Steve
On Tue, Jul 29, 2014 at 1:50 PM, Stadem, Richard D. <
[log in to unmask]> wrote:
> Yes, they do look like microvias. Plugged during fabrication and blown
> open by the reflow process.
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Robert Kondner
> Sent: Tuesday, July 29, 2014 2:31 PM
> To: [log in to unmask]
> Subject: Re: [TN] Trying to figure out possible mechanism for contamination
>
> I still think they look a lot like vias but some would have to be micro
> vias.
>
> Yes, the consistent "Roundness" sure looks like via clearance etch back.
>
> But it is SO SIMPLE - Are there holes? :-)
>
> Bob K.
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of David Hillman
> Sent: Tuesday, July 29, 2014 3:21 PM
> To: [log in to unmask]
> Subject: Re: [TN] Trying to figure out possible mechanism for contamination
>
> Hi gang - I had the same first impression as Dick that these were solder
> splatters from reflow/wave/stencil but when I looked closer, it the
> splatters are very very uniform in size plus the center "dot' is equally
> uniform. Someone had mention a filled micro via delamin-ish problem could
> be the root cause. Take a look at the photo again - doesn't it seem that
> these are too uniform for a solder splatter root cause?
>
> Dave Hillman
> Rockwell Collins
> [log in to unmask]
>
>
> On Tue, Jul 29, 2014 at 11:30 AM, Richard Krug <[log in to unmask]> wrote:
>
> > To me it looks like solder paste spatter / fines that landed on ENIG
> > surface. Can be caused by too steep a ramp rate during preheat stage
> > of reflow profile. Was measured reflow profile within manufacturer's
> spec?
> >
> > Dick Krug, CSSBB, CSMTPE
> > Lead Process Engineer
> > Sparton Brooksville, LLC
> > 30167 Power Line Road
> > Brooksville, FL 34602-8299
> > p (352) 540-4012 (Internal Ext. 2012) [log in to unmask]
> >
> > -----Original Message-----
> > From: TechNet [mailto:[log in to unmask]] On Behalf Of John Foster
> > Sent: Tuesday, July 29, 2014 12:13 PM
> > To: [log in to unmask]
> > Subject: [TN] Trying to figure out possible mechanism for
> > contamination
> >
> > We have been seeing a problem recently on several different CCA'S that
> > we are having assembled.
> > The boards are ENIG with plug and plate. The assembly shop is
> > assuring us that these gold areas are being Protected during the
> > entire assembly process with kapton tape.
> > I was thinking it was flux splatter since the areas are always almost
> > perfectly circular.
> > The locations are very random and range from nothing to what is in the
> > picture.
> > Is there any other mechanism that might be causing this? On our next
> > run I am going to go to the shop To witness the taping. But I was
> > curious if maybe it's some other cause.
> > Mr. Gregory was kind enough to post a picture.
> > http://stevezeva.homestead.com/spots.jpg
> >
> > Any thoughts would be appreciated
> > Thank You
> > John Foster
> > L3 Communicatons
> >
> > Confidentiality Notice: The information contained in this message is
> > intended only for the use of the addressee, and may be confidential
> > and/or privileged. If the reader of this message is not the intended
> > recipient, or the employee or agent responsible to deliver it to the
> > intended recipient, you are hereby notified that any dissemination,
> > distribution of copying of this communication is strictly prohibited.
> > if you have received this communication in error, please notify the
> sender immediately.
> >
> > Warning: This document may contain technical data within the
> > definition of the International Traffic in Arms Regulation (ITAR) and
> > is subject to the export control laws of the U.S. Government.
> > Transfer of this data by any means to a foreign person, whether in the
> > United States or abroad, without an export license or other approval
> > from the U.S. Department of State, is strictly prohibited
> >
> >
> > ______________________________________________________________________
> > This email has been scanned by the Symantec Email Security.cloud service.
> > For more information please contact helpdesk at x2960 or
> > [log in to unmask]
> > ______________________________________________________________________
> >
> > ______________________________________________________________________
> > This email has been scanned by the Symantec Email Security.cloud service.
> > For more information please contact helpdesk at x2960 or
> > [log in to unmask]
> > ______________________________________________________________________
> >
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or [log in to unmask]
> ______________________________________________________________________
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or [log in to unmask]
> ______________________________________________________________________
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or [log in to unmask]
> ______________________________________________________________________
>
--
This email and any attachments are only for use by the intended
recipient(s) and may contain legally privileged, confidential, proprietary
or otherwise private information. Any unauthorized use, reproduction,
dissemination, distribution or other disclosure of the contents of this
e-mail or its attachments is strictly prohibited. If you have received this
email in error, please notify the sender immediately and delete the
original.
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
