Gerry, they are 0.125" I believe.
_____________________________________________________________________________________
Henry Rekers P. Eng | Schneider Electric | Global Supply Chain |
Senior Manufacturing Engineer
Phone: +1-250-652-7100 ext. 7510 | Toll Free: +1-866-466-7627 ext.
7510 | Fax: +1-250-544-2390 |
Email: [log in to unmask] | Site:
www.schneider-electric.com | Address: 2195 Keating Cross Road,
Saanichton, BC, Canada, V8M 2A5
*** Please consider the environment before printing this e-mail
From:
Gerry Gagnon <[log in to unmask]>
To:
<[log in to unmask]>,
Date:
06/10/2014 11:31 AM
Subject:
Re: [TN] Plating in non-plated holes - again
Sent by:
TechNet <[log in to unmask]>
Hi Henry,
What is the diameter of NPTH?
Best regards,
Gerry
> Date: Tue, 10 Jun 2014 11:25:39 -0700
> From: [log in to unmask]
> Subject: Re: [TN] Plating in non-plated holes - again
> To: [log in to unmask]
>
> That's what I think, but we're getting push back from the supplier and I
> was hoping to get more specific.
>
> Thanks.
>
>
_____________________________________________________________________________________
>
>
> Henry Rekers P. Eng | Schneider Electric | Global Supply Chain |
> Senior Manufacturing Engineer
> Phone: +1-250-652-7100 ext. 7510 | Toll Free: +1-866-466-7627 ext.
> 7510 | Fax: +1-250-544-2390 |
> Email: [log in to unmask] | Site:
> www.schneider-electric.com | Address: 2195 Keating Cross Road,
> Saanichton, BC, Canada, V8M 2A5
> *** Please consider the environment before printing this e-mail
>
>
>
> From:
> David Hillman <[log in to unmask]>
> To:
> <[log in to unmask]>,
> Date:
> 06/10/2014 10:08 AM
> Subject:
> Re: [TN] Plating in non-plated holes - again
> Sent by:
> TechNet <[log in to unmask]>
>
>
>
> Hi Henry - maybe I am making this too simple but if your drawing/design
> data shows a nonplated thru hole, then having any plating in it, partial
> or
> complete, is a violation of the drawing and therefore a nonconformance.
>
> Dave
>
>
> On Tue, Jun 10, 2014 at 10:26 AM, Henry Rekers <
> [log in to unmask]> wrote:
>
> > Hey there technetters. A while back, I sent a message about enig
> plating
> > contamination in NON-plated holes. I've bounced it back to the board
> > shop saying that it is unacceptable, but they claim it is due to 6012
> > 3.5.2
> > I also think it's unacceptable in the 4552 spec. The design
> > documentation clearly states non-plated. It's not plated, just
> partially
> > plated.
> >
> > Any advice?
> >
> > Thanks.
> >
> >
>
_____________________________________________________________________________________
> >
> >
> > Henry Rekers P. Eng | Schneider Electric | Global Supply Chain |
> > Senior Manufacturing Engineer
> > Phone: +1-250-652-7100 ext. 7510 | Toll Free: +1-866-466-7627 ext.
> > 7510 | Fax: +1-250-544-2390 |
> > Email: [log in to unmask] | Site:
> > www.schneider-electric.com | Address: 2195 Keating Cross Road,
> > Saanichton, BC, Canada, V8M 2A5
> > *** Please consider the environment before printing this e-mail
> >
> > ______________________________________________________________________
> > This email has been scanned by the Symantec Email Security.cloud
> service.
> > For more information please contact helpdesk at x2960 or
> [log in to unmask]
> > ______________________________________________________________________
> >
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud
service.
> For more information please contact helpdesk at x2960 or
[log in to unmask]
> ______________________________________________________________________
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud
service.
> ______________________________________________________________________
>
>
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud
service.
> For more information please contact helpdesk at x2960 or
[log in to unmask]
> ______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
