I know I am late chiming in, but how are non-plated through holes not secondary drilling requirements? Your drawing requirement for NPTH would supercede any fabrication specification. Or am I wrong?
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard D.
Sent: Tuesday, June 10, 2014 11:35 AM
To: [log in to unmask]
Subject: Re: [TN] Plating in non-plated holes - again
Secondary drilling of holes already drilled is not secondary drilling, however. It is rework. Rework of defects that should have been found and fixed in the first place.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Henry Rekers
Sent: Tuesday, June 10, 2014 10:52 AM
To: [log in to unmask]
Subject: Re: [TN] Plating in non-plated holes - again
I'd love to do that, but our specification demands no secondary drilling.
My guess is due to past registration issues.
_____________________________________________________________________________________
Henry Rekers P. Eng | Schneider Electric | Global Supply Chain |
Senior Manufacturing Engineer
Phone: +1-250-652-7100 ext. 7510 | Toll Free: +1-866-466-7627 ext.
7510 | Fax: +1-250-544-2390 |
Email: [log in to unmask] | Site:
www.schneider-electric.com | Address: 2195 Keating Cross Road,
Saanichton, BC, Canada, V8M 2A5
*** Please consider the environment before printing this e-mail
From:
Brian Ellis <[log in to unmask]>
To:
TechNet E-Mail Forum <[log in to unmask]>,
[log in to unmask],
Date:
06/10/2014 08:38 AM
Subject:
Re: [TN] Plating in non-plated holes - again
Drill after ENIG
Brian
On 10.06.2014 18:26, Henry Rekers wrote:
> Hey there technetters. A while back, I sent a message about enig
plating
> contamination in NON-plated holes. I've bounced it back to the board
> shop saying that it is unacceptable, but they claim it is due to 6012
> 3.5.2
> I also think it's unacceptable in the 4552 spec. The design
> documentation clearly states non-plated. It's not plated, just
partially
> plated.
>
> Any advice?
>
> Thanks.
>
_____________________________________________________________________________________
>
>
> Henry Rekers P. Eng | Schneider Electric | Global Supply Chain |
> Senior Manufacturing Engineer
> Phone: +1-250-652-7100 ext. 7510 | Toll Free: +1-866-466-7627 ext.
> 7510 | Fax: +1-250-544-2390 |
> Email: [log in to unmask] | Site:
> www.schneider-electric.com | Address: 2195 Keating Cross Road,
> Saanichton, BC, Canada, V8M 2A5
> *** Please consider the environment before printing this e-mail
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud
service.
> For more information please contact helpdesk at x2960 or
[log in to unmask]
> ______________________________________________________________________
>
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
________________________________
This message and any attachments are solely for the use of the addressee and may contain L-3 proprietary information that may also be defined as USG export controlled technical data. If you are not the intended recipient, any disclosure, use or distribution of its content is prohibited. Please notify the sender by reply e-mail and immediately delete this message and any attachments.
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|