TECHNET Archives

December 2013

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Theodore J Tontis <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, [log in to unmask]
Date:
Mon, 9 Dec 2013 18:48:38 +0000
Content-Type:
text/plain
Parts/Attachments:
text/plain (215 lines)
I am not a Ford guy so the statement about the Pinto being a POS well...  

I do not think anyone said that a Vega or a Pinto is going to be a POS but you get what you pay for.  

A Vega and a Pinto will still serve the function as a Porsche, get a person from point A to point B. However, the Porsche will perform to a higher standard than the other two. The reason being it is that the Porsche is designed and manufactured using different standards than the Pinto or Vega.

The standards for high reliable electronics are not the same as general consumer products. I do not believe that someone would call out or use the same manufacturing or design standards needed on a life support system for a consumer product, it's just not cost effective or practical.  If one wants high-end electronics than one should document the requirements is all I am saying. 

Ted T

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard D.
Sent: Monday, December 09, 2013 11:08 AM
To: [log in to unmask]
Subject: Re: [TN] Crazing

I absolutely agree with Syed. Just because it is a Pinto or a Vega does not mean it has to be a POS.

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Ahmad, Syed
Sent: Monday, December 09, 2013 10:37 AM
To: [log in to unmask]
Subject: Re: [TN] Crazing

Why should an engineer or a manufacturer or a seller think so of a Pinto customer and deliver a substandard product? Quality and reliability beyond the documented text should be the pride of a designer, a manufacturer and a seller. Price of a product should limit amenities (power, space, leather seats or cloth) and not compromise the pride and diligence in design and manufacture.

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Theodore J Tontis
Sent: Monday, December 09, 2013 10:23 AM
To: [log in to unmask]
Subject: Re: [TN] Crazing

I agree with what you are saying and would add, any requirement that is needed above and beyond a standard should be documented on the prints. Failure to do so is at the end use customers risk.  No one should expect a supplier to accept a non-conformance or material rejection by a customer to requirements that are not stated beforehand or agreed on. 

If I am manufacturing a Porsche I am going to have more CTQ's and document higher standards than if I was building a Pinto and, my supplier would have that information. If the documentation is not clear who is at fault, the supplier? 

I do not believe there was a class given to the bare board being evaluated so the default class would be what the board house produces as a standard.

It would appear there were no specific notes or documentation that indicate to the supplier they would be held to a higher standard or tighter requirement than the standard used by the board house.

I go back to my original statement that it should be investigated further and if necessary make adjustments to the process. If multiple random samples were taken with the same results there might be something worth digging into. Also, If a higher standard is required document it on the print or talk to the supplier to insure there is a clear understanding of what is required.

Ted T.  

-----Original Message-----
From: Joyce Koo [mailto:[log in to unmask]]
Sent: Monday, December 09, 2013 9:35 AM
To: 'TechNet E-Mail Forum'; Tontis, Theodore J
Subject: RE: [TN] Crazing

That is a design call - depend upon the application and design redundancy.  If it is space program and intended for years of use without redundancy, it wouldn't be a indicator to me if there is deviation from qualification specimen, for example.  (I purchasing service - pwb, based on the sample = qual specimen; if I show you a Porsche prior to contract and deliver a pinto after you pay... hmmm, may be a good deal... Theodore, what you are buying next time? - I'll indicate it is a process indicator since it runs equally from your home to work).   

Joyce Koo
Researcher
Materials Interconnect Lab
Office: (519) 888-7465 79945
BlackBerry: (226) 220-4760

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Theodore J Tontis
Sent: Monday, December 09, 2013 9:42 AM
To: [log in to unmask]
Subject: Re: [TN] Crazing

Why wouldn't it just be considered a process indicator? 

After all, a process indicator is not a defect and it indicates a non-desired output that would warrant further investigation or counter measures to correct? The material is still deemed acceptable just not ideal.

I do believe it is not a defect and agree if we were to identify every concern found under magnification above the specified/agreed upon requirement, there would be a long list of issues to address and costs would skyrocket.  Isn't that why we have standards for this sort of thing?

Ted T

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard D.
Sent: Monday, December 09, 2013 6:52 AM
To: [log in to unmask]
Subject: Re: [TN] Crazing

I am not sure I accept that "along the way" theory completely.
Prevalent in all of the IPC standards, all defect categories are provided a magnification level for inspection. For example, if a non-metallic particle is seen on the PWB while inspecting solder joints at 20X magnification on a conformal coated CCA, the inspector is supposed to switch to the required magnification for the particulate matter (4X-7X). If the particulate matter cannot be seen at that range, it is not considered to be a defect. 
If you want to entertain your "along the way" theory, then have fun counting up the rework hours to strip away the coating, remove the particles, clean, dry, and re-coat. No matter what you do short of building all product in a Class 10 clean room, this unnecessary rework will never end.

Of course, one must understand that there are certain exceptions to this; I am just saying that you cannot allow an "along the way" philosophy in the factory. It will put you out of business.
In regards to your example, two questions come to mind:

1. What is the magnification required when inspecting for particulate matter between conductors at the PWB level, and what is the minimum electrical clearance between the two traces you describe? If the material was visible at the required magnification, it was an escape, and should have been caught at the higher magnification you describe anyway, and is a real defect.
2. Did you measure the resistance again after the tiny piece of material was removed, and did it make any difference?


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Gerry Gagnon
Sent: Friday, December 06, 2013 7:21 AM
To: [log in to unmask]
Subject: Re: [TN] Crazing

Hi Paul,
 
Hope you and Bill B. are doing fine.
 
I am assuming that you you were looking for something else and detected a "non-conforming" level of crazing.
 
In my mind, this is an easy one because you found the non-conformance "along the way" while examining your microsection.
 
Let me give you an easier analogy.
 
While examining a region of an IST test coupon in transverse mount, I find a tiny piece of material bridging two conductors at high mag.
Clearing away  the conductor surfaces enough to measure if there is a resistance, I get a value in the MegOhm range.
 
Is it a short?
 
Unless things gave changed, Bare board continuity thresholds will not detect this phenomenon.
Let's also say that innerlayer AOI (if performed) has a very high escape rate for this type of phenomenon or may not even detect it at all.
 
Is the phenomonon a short per IPC A-610?
My answer is yes, it is an unwanted connection, albeit a high resistance connection, and is difficult to detect. 
 
Does the fact that I found this short in a cross section under high magnification, while I was looking for something else, change anything?
 
I don't think so, and I do not think IPC A-610 allows non-conformances that are found "along the way". 
 
Have a good one.
Gerry
 
 

 
> Date: Thu, 5 Dec 2013 16:05:41 -0500
> From: [log in to unmask]
> Subject: [TN] Crazing
> To: [log in to unmask]
> 
> I was just on a conference call where we found crazing (a separation 
> between glass fibers and the epoxy system), in a microsection. The 
> fabricator stated that this had to be evaluated looking at a board 
> macroscopically and could not be evaluated microscopically.
> 
>  
> 
> Crazing is called out in IPC-A- 600 in section 2, paragraph 2.3.2 page 
> 18, which is "Externally Observable Characteristics". In A-600 there 
> is picture of a microsection showing the defect but it states that a 
> microsection is not required.
> 
>  
> 
> In IPC 6012-2010 crazing is call out in 3.3.2.2, page 12, which states 
> (I am paraphrasing), "Crazing shall not violate greater than 50% of 
> the distance between adjacent conductors..." The document then refers 
> to IPC A 600.
> 
>  
> 
> What is your take on their argument that crazing should not be 
> evaluated microscopically as per IPC?
> 
>  
> 
> Sincerely,
> 
>  
> 
> Paul Reid
> 
> Program Coordinator
> 
> PWB Interconnect Solutions Inc. 
> 235 Stafford Rd., West, Unit 103
> Nepean, Ontario Canada, K2H 9C1
> 
> 613 596 4244 ext. 229
> 
> Skype paul_reid_pwb
> [log in to unmask]
> 
>  
> 
> 
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or 
> [log in to unmask] 
> ______________________________________________________________________
 		 	   		  

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
---------------------------------------------------------------------
This transmission (including any attachments) may contain confidential information, privileged material (including material protected by the solicitor-client or other applicable privileges), or constitute non-public information. Any use of this information by anyone other than the intended recipient is prohibited. If you have received this transmission in error, please immediately reply to the sender and delete this information from your system. Use, dissemination, distribution, or reproduction of this transmission by unintended recipients is not authorized and may be unlawful.

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

ATOM RSS1 RSS2