Main issue I see is you do not specify whether you want to start with 1 oz. copper on the outers or finish with 1 oz. Regards Steve Kelly

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Yoch, Brian
Sent: November-22-13 12:09 PM
To: [log in to unmask]
Subject: Re: [TN] PCB stack up question

I used to sweat the stackup differences between vendors. But after talking to several reps face to face and over the phone I am no longer too attached to my stackup. The stackup that we call out is nothing more than a guideline for the CM to reference, because no 2 CMs will have the exact same process.

Brian Y. 

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Theodore J Tontis
Sent: Friday, November 22, 2013 10:11 AM
To: [log in to unmask]
Subject: [TN] PCB stack up question

I have a 6 layer stack up specified on my gerbers as:

0.0004 mil solder mask
0.0014 mil top layer 1oz copper
0.0086 mil 2 X 2116 prepreg
0.0014 mil inner 1 1oz copper
0.0140 mil core
0.0014 mil inner 2 1oz copper
0.0086 mil 2 X 2116 prepreg
0.0014 mil inner 3 1oz copper
0.0140 mil core
0.0014 mil inner 4 1oz copper
0.0086 mil 2 X 2116 prepreg
0.0014 mil bottom layer 1oz copper
0.0004 mil solder mask

0.0620 mil total stack up +/- 0.006

Our CM's vendor is requesting I change either
A: adjust the 14mil core to 12mil to meet 62±6mil finished thickness.
B: relax the finished thickness to 65±6mil..
C: control the board thickness with 62±6mil exclude the solder mask thickness.

Their stack up is as follows:

0.0005 mil solder mask
0.0020 mil top layer 1oz copper
0.0091 mil 2 X 2116 prepreg
0.0012 mil inner 1 1oz copper
0.0142 mil core
0.0012 mil inner 2 1oz copper
0.0085 mil 2 X 2116 prepreg
0.0012 mil inner 3 1oz copper
0.0142 mil core
0.0012 mil inner 4 1oz copper
0.0091 mil 2 X 2116 prepreg
0.0020 mil bottom layer 1oz copper
0.0005 mil solder mask

0.0649 mil total stack up +/- 0.006

I got my stack up from a local vendor I've worked with in the past.
Our CM has measured some of their bare boards at 0.070 and 0.071 mil thick.

Which stack up is correct or am I missing something important?


Ted T.


Theodore J. Tontis CID
Senior Manufacturing Engineer
[cid:[log in to unmask]]<http://www.eaton.com/>
11131 Adams Road
Franksville, WI 53126
Office 262-835-1552
Cell 262-510-3145
Fax 262-835-1544


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
This message is intended only for the named recipient. If you are not the intended recipient, you are notified that disclosing, copying, distributing or taking any action based on the contents of this information is strictly prohibited.
 
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________