So you can solve Schrödinger's cat riddle.
Dewey

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Inge Hernefjord
Sent: Wednesday, August 28, 2013 1:10 PM
To: [log in to unmask]
Subject: Re: [TN] Blowing Smoke

When our cat farts, a very smal amount of gas is spread all over the room and remains constant pretty long..

Inge


On 28 August 2013 11:21, Stadem, Richard D. <[log in to unmask]>wrote:

> Find out how particle counters are calibrated. There must be a 
> procedure somewhere. Then figure out a way to make it cheaper and easier to use.
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Wayne Thayer
> Sent: Wednesday, August 28, 2013 12:09 PM
> To: [log in to unmask]
> Subject: Re: [TN] Blowing Smoke
>
> Hi Phil-
>
> No problem with organics.
>
> This is a good direction to consider:  An electronic cigarette.  They 
> contain the micro-heater to vaporize the propylene glycol.  I can 
> probably make that controlled by the Arduino I'm using, and pulse 
> width modulate it to adjust how much comes out.  I may need an 
> additional blower of some kind in the system, but that sounds pretty easy.
>
> I'll let you know what I find out.
>
> Thanks,
>
> Wayne
>
>
> -----Original Message-----
> From: [log in to unmask] [mailto:[log in to unmask]]
> Sent: Wednesday, August 28, 2013 11:25 AM
> To: TechNet E-Mail Forum; Wayne Thayer
> Subject: RE: [TN] Blowing Smoke
>
> Heat up propylene glycol, oh wait, you need inorganic particulates, right?
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Wayne Thayer
> Sent: Wednesday, August 28, 2013 8:07 AM
> To: [log in to unmask]
> Subject: [TN] Blowing Smoke
>
> OK, here's another problem I've been playing with (although it has 
> little to do with IPC mission, it might be related).
>
> I am trying to build a system for measuring airborne particulates for 
> humanitarian organizations looking for inexpensive ways to 
> measure/monitor indoor air quality.  There are cheap sensors available 
> which might do the job, but they would need periodic re-calibration.
>
> So I need a controlled, extremely small amount of smoke.  At first, I 
> thought this would be trivial:  Find a cheap part at DigiKey and put 
> too many watts through it.  Way too much smoke and too little control.  
> Then I tried burning thin wires.  Too irregular because sometimes they 
> incinerate completely and other times they find a tiny defect and just 
> burn that until the wire stops conducting.  Then I tried just heating 
> the wire enough to burn off the insulation.  Still too irregular!  I 
> did just a few experiments and got 30% variation.
>
> Now I'm starting to think maybe a tiny piece of paper on an automotive 
> cigarette lighter.  That's a lot of power to get that glowing, and it 
> is not convenient to attach to.  Any other ideas?
>
> Wayne
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or 
> [log in to unmask]
> ________________
> ________________________________
>  This message and any attachments are solely for the use of the 
> addressee and may contain L-3 proprietary information that may also be 
> defined as USG export controlled technical data. If you are not the 
> intended recipient, any disclosure, use or distribution of its content 
> is prohibited. Please notify the sender by reply e-mail and 
> immediately delete this message and any attachments.
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or 
> [log in to unmask]
> ________________
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or 
> [log in to unmask] 
> ______________________________________________________________________
>


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________