Subject: | |
From: | |
Reply To: | |
Date: | Mon, 22 Jul 2013 15:41:06 +0200 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Hello Lyon,
You may look to the IPC A-610E at chapter 4.3.2 pag. 4-15 for references
on lifted pads for press-fit.
Regards.
Francesco
Francesco Di Maio
IPC e Formazione
Via Kennedy Ingresso 2, 20871 Vimercate (MB) - Italy
Desk: +39.039.639.5921 - Mobile: +39.335.5693650 - Fax: +39.039.639.5051
E-Mail:[log in to unmask]
GEST Labs S.r.l. a Socio Unico
Societa’ soggetta a direzione e coordinamento da parte di SEM S.r.l. ai
sensi dell’Art. 2497 bis c.c.
Codice Fiscale, Partita IVA e Registro delle Imprese di Milano N
07602270964 – N. R.E.A. 1970226 - Capitale sociale € 500.000 interamente
versato
Sede Legale: Piazza Santa Maria Beltrade,.2 - 20123 Milano - Uffici
Amministrativi e Stabilimento di Vimercate Via Lecco, 61 20871 Vimercate
MB
Please visit us at: www.GESTLabs.it and www.SemTechnologies.it
<< Rispetta l'ambiente. Non stampare questa mail se non è necessario >>
------ CONFIDENTIALITY & PRIVACY NOTICE ------
This e-mail message and any file transmitted with it, contains
confidential or proprietary information.
If you are not the intended recipient of this e-mail, please be informed
that any use of the content hereof is prohibited.
You are requested to notify immediately the sender and delete the content
you received.
"Stadem, Richard D." <[log in to unmask]>
Sent by: TechNet <[log in to unmask]>
22/07/2013 15.13
Please respond to
TechNet E-Mail Forum <[log in to unmask]>; Please respond to
"Stadem, Richard D." <[log in to unmask]>
To
<[log in to unmask]>
cc
Subject
Re: [TN] Regarding on press-fit connector lifted
Perhaps no response because I, for one, do not understand what you are
asking. Is the connector not flush to the PWB? Or is there a lifted pad?
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Lyon Yuan
Sent: Saturday, July 20, 2013 7:33 PM
To: [log in to unmask]
Subject: Re: [TN] Regarding on press-fit connector lifted
Any reply?
Lyon Yuan
-----Original Message-----
From: [log in to unmask] [mailto:[log in to unmask]] On Behalf Of
Lyon Yuan
Sent: Saturday, July 20, 2013 7:11 PM
To: [log in to unmask]
Subject: [TN] Regarding on press-fit connector lifted
Importance: High
Hi Folks,
What's the standard on press-fit connector lifted?
Lyon Yuan
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
|
|