Not really, the retiree brought Kodak. It might have hope. I think.
Joyce Koo
Researcher
Materials Interconnect Lab
Office: (519) 888-7465 79945
BlackBerry: (226) 220-4760
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Dennis Fritz
Sent: Friday, May 10, 2013 4:13 PM
To: [log in to unmask]
Subject: [TN] NTC Re: [TN] DYNASOLVE 100
Hmm, not really a Kodak moment. Eastman chemical was spun out on the way to Kodak bankruptcy, to try to raise cash to support the failing silver film business. Only Kodak moments I have seen recently were patent sales, and possible plan to get out of bankruptcy.
-----Original Message-----
From: Whittaker, Dewey (EHCOE) (EHCOE) <[log in to unmask]>
To: TechNet <[log in to unmask]>
Sent: Fri, May 10, 2013 3:37 pm
Subject: Re: [TN] DYNASOLVE 100
A Kodak moment: that's a rare development anymore.
ewey
-----Original Message-----
rom: TechNet [mailto:[log in to unmask]] On Behalf Of Steven Creswick
ent: Friday, May 10, 2013 12:32 PM
o: [log in to unmask]
ubject: Re: [TN] DYNASOLVE 100
Victor,
I didn't realize the Dynaloy had been dissolved into Eastman! Thanks! I
earned something today.
Check out http://www.dynaloy.com/products-by-name.html for the data sheet.
oesn't appear as though it needs to be heated.
My experience with the Dynaloy products is that time and temp are critical.
nce you find the sweet spot, you can remove all manner of materials, but do
ave a really good hood! Most of the stuff reeks worse than a dead skunk that
as been laying by the roadside for days in the hot sun.
I note that the Dynasolve 100 is only good for removing polymers, so it will
ake the parts marking info off the chip resistor, but in the olden days we used
o use a low temp glass frit to passivate the surface of the resistor.
on't believe that the Dynalloy 100 will be of much help there.
teve Creswick
r Associate - Balanced Enterprise Solutions http://www.linkedin.com/in/stevencreswick
616 834 1883
-----Original Message-----
rom: TechNet [mailto:[log in to unmask]] On Behalf Of Victor Hernandez
ent: Friday, May 10, 2013 3:13 PM
o: [log in to unmask]
ubject: [TN] DYNASOLVE 100
Fellow TechNetters:
It's been a very long time since I last tried to remove the coating from a
eramic film resistor. I am using the above product but unable to remember the
emperature setting.
Victor,
______________________________________________________________________
his email has been scanned by the Symantec Email Security.cloud service.
or more information please contact helpdesk at x2960 or [log in to unmask]
_____________________________________________________________________
_____________________________________________________________________
his email has been scanned by the Symantec Email Security.cloud service.
or more information please contact helpdesk at x2960 or [log in to unmask]
_____________________________________________________________________
______________________________________________________________________
his email has been scanned by the Symantec Email Security.cloud service.
or more information please contact helpdesk at x2960 or [log in to unmask]
_____________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------------------------
This transmission (including any attachments) may contain confidential information, privileged material (including material protected by the solicitor-client or other applicable privileges), or constitute non-public information. Any use of this information by anyone other than the intended recipient is prohibited. If you have received this transmission in error, please immediately reply to the sender and delete this information from your system. Use, dissemination, distribution, or reproduction of this transmission by unintended recipients is not authorized and may be unlawful.
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
