Sender: |
|
X-To: |
|
Date: |
Thu, 21 Mar 2013 16:25:42 +0000 |
Reply-To: |
|
Message-ID: |
|
Subject: |
|
From: |
|
MIME-Version: |
1.0 |
In-Reply-To: |
|
Content-Transfer-Encoding: |
quoted-printable |
Content-Type: |
text/plain; charset="us-ascii" |
Parts/Attachments: |
|
|
I would think that through a bit:
"Note that even the smallest trace of moisture may result in a steam explosion, spattering burning molten metal around."
http://www.chemistrydaily.com/chemistry/Fire_extinguisher
I think sand would be a better alternative, but a few hundred lbs. of solder on a RT floor won't go far before it freezes.
Ed Popielarski
Engineering Manager
970 NE 21st Ct.
Oak Harbor, Wa. 98277
Ph: 360-675-1322
Fx: 206-624-0965
Cl: 949-581-6601
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Goodyear, Patrick
Sent: Wednesday, March 20, 2013 8:07 PM
To: [log in to unmask]
Subject: Re: [TN] Solder pot capacity of Vitronics/Soltec 6622CC Wave solder machine
Have a CO2 fire extinguisher handy to solidify i.e. freeze -100 degF the moving molten metal mass.
Just a thought
pat
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Mike Fenner
Sent: Wednesday, March 20, 2013 6:42 AM
To: [log in to unmask]
Subject: Re: [TN] Solder pot capacity of Vitronics/Soltec 6622CC Wave solder machine
Ho!
Too right.
I offer to the advice pile:
Attend to your PPE; specifically don't wear synthetic fabrics/footwear when messing with molten metal.
Do wear proper gloves, appropriate eye protection.
Don't trust drain valves; especially don't trust electric drain valves. They easily jam open.
[Think about how far molten solder will spread and how far /fast you will need to go to keep ahead of spilling metal. Further /faster than you ever thought possible in both instances :)] With used/unknown equipment make sure everything is dry and free of anything volatile. You don't want an "Old Faithfull" experience.
I thought we already addressed the top up issue, at least theoretically in an earlier go round: subject to analysis you could leave the SAC in there.
Of course a few hundred pounds of SAC is worth a lot more pounds of Sn/PB and can be traded to reduce fill cost. This would be lost if you left it in machine.
Best Wishes
Mike
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Larry Dzaugis
Sent: Tuesday, March 19, 2013 8:11 PM
To: [log in to unmask]
Subject: Re: [TN] Solder pot capacity of Vitronics/Soltec 6622CC Wave solder machine
I had a runaway pot in Thailand on a Select Machine.
Pot drained and insides fried.
Not pretty and expensive to fix.
Manufacturer put in redundant sensor after that.
Read the manufactures instructions and ask them questions.
I had a Tech tell me that I couldn't be an Engineer because I cheated, I read the instructions first.
Electronics uses benign equipment for the most part.
European guarding and few high kinetic parts.
Solder pots and the insides of the turret machines can crush, burn or kill.
Even the Sr Tech had solder splash on his face doing routine maintenance.
Wear eye protection at a minimum.
Engineers and techs are notorious for skating on safety to check something out.
Typically the solder guys have a few scars from inadvertent touches with something hot whether solder pallets, pots or solder.
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
PG&E is committed to protecting our customers' privacy.
To learn more, please visit http://www.pge.com/about/company/privacy/customer/
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
|
|