TECHNET Archives

December 2012

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Phil Bavaro <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, [log in to unmask]
Date:
Wed, 5 Dec 2012 17:29:53 +0000
Content-Type:
text/plain
Parts/Attachments:
text/plain (136 lines)
Hi Inge,

Old legs or not, your input is always appreciated.  Joyce has it right.

Phil

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Inge Hernefjord
Sent: Wednesday, December 05, 2012 8:55 AM
To: [log in to unmask]
Subject: Re: [TN] Termination finishes, Cu thickness under Ag, Au-Pt-Pd

Hi Wayne & collegues,

heard from Joyce that you missed my comments. Sorry for that. When Steve Gregory faded away as kind of bagpipe blower in the TN brigade, I lost some contact with the troops march and became last one and with time I saw the troops at distance. Well, with  my old legs, seems as I have to get lift with a jeep and catch up with you.

On the theme you just discuss with Julie, I'd say to her not to mix with changing the component finish immediately. Doing such things can end in a never-ending-process. I am not updated with what is actually going on, so my advice may not be of any help, but there is one soldering method that have a very generous process window and that is VPS, Vapour Phase Soldering. It has some very attractive advantages, like instant and simultaneous heating, extremly low Oxygen presence and is very fast. All properties that makes even many poor weldable>acceptable weldable. You may not be able to try this, of some reason. Just wanted to put up a finger and feel the wind direction

Inge

On 5 December 2012 00:41, Thayer, Wayne - IS <[log in to unmask]>wrote:

> Hi Julie-
>
> Sorry for the late response.  I have a lot of experience with this or
> similar material.  Yes, burnishing helps.  I also deliberately use an
> iron tip that doesn't wet well.  Paste with SMT works too, and is more
> controllable.  We typically used the SnPbAg alloy with about 2%Ag, but
> I don't know if that helped.  Our rule of thumb was you got three
> shots to solder to it, IF you used pre-heat and were very careful.
> BUT, this product is cake to solder to compared with AgPd, which most
> of the thick film commercial products used.  That stuff would only
> survive a very carefully controlled single reflow.
>
> One thing we learned is that the leach rate SKYROCKETS if the designer
> put the PtPdAu directly on top of thick film Au where the solder was
> going to be.  That recipe leaches just as bad as plain gold.  The
> overlap MUST be behind a solder dam.  (The thick film vendors only
> tell you this AFTER you figure it out on your own!)  By the way, plain
> gold solders just fine on ceramic using SnAu eutectic solder.  It is
> very expensive and is quite hot (270C or so).  The joints are very pretty shiny silver and very strong.
>  You can also weld copper wires to thick film gold or silver.
> MiniCircuits sells piles of RF parts containing tiny transformers
> attached this way, and this technique is also used on RF inductors
> which are wound on an alumina mandrel.
>
> We ended up having a low temperature copper put on top of the gold
> whenever we could.  It is much more robust--still wets horribly though!
>
> Wayne Thayer
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Steven Creswick
> Sent: Wednesday, November 28, 2012 8:59 AM
> To: [log in to unmask]
> Subject: Re: [TN] Termination finishes, Cu thickness under Ag,
> Au-Pt-Pd
>
> Julie,
>
> Yes, the addition of a small amount of Pt does slow up the rate of the
> conductors leaching into the solder.  From practical experience, the
> more Pt is added, the better the leach resistance.  However, the more
> Pt is added, the greater are wetting problems.
>
> Thick film ink suppliers [used to] offer inks with different amounts
> of Pt so you could slightly 'chose your poison.'
>
> Also can depend on whether it is a fritted, or a frit-less, system.
>
> Like Mike says - BURNISH before solder IS the general rule!
>
> Never was something you really 'wanted' to solder to, unless you had
> no other choice.
>
>
> Steve Creswick
> Sr Associate - Balanced Enterprise Solutions
> http://www.linkedin.com/in/stevencreswick
>                          616 834 1883
>
>
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Julie Silk
> Sent: Tuesday, November 27, 2012 8:02 PM
> To: [log in to unmask]
> Subject: Re: [TN] Termination finishes, Cu thickness under Ag,
> Au-Pt-Pd
>
> The claim of the supplier is that the Pt prevents the Au from
> dissolving into the solder.  Hmmm.  Can anyone back that up?
> The recent info on this is that it's looking like a wettability
> problem more than a dissolving-into-the-joint problem, although
> neither is confirmed.
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or
> [log in to unmask]
> ________________
>
> ________________________________
>
> Email addresses of ITT Exelis employees have changed from itt.com to
> exelisinc.com. Please update your favorites and contact information to
> reflect these changes.
>
> This e-mail and any files transmitted with it may be proprietary and
> are intended solely for the use of the individual or entity to whom
> they are addressed. If you have received this e-mail in error please
> notify the sender. Please note that any views or opinions presented in
> this e-mail are solely those of the author and do not necessarily
> represent those of Exelis Inc. The recipient should check this e-mail
> and any attachments for the presence of viruses. Exelis Inc. accepts
> no liability for any damage caused by any virus transmitted by this e-mail.
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or
> [log in to unmask]
> ______________________________________________________________________
>


______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
________________________________
 This message and any attachments are solely for the use of the addressee and may contain L-3 proprietary information that may also be defined as USG export controlled technical data. If you are not the intended recipient, any disclosure, use or distribution of its content is prohibited. Please notify the sender by reply e-mail and immediately delete this message and any attachments.

______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

ATOM RSS1 RSS2