Do time Zero, 3x and 6x samples also exhibit fractures?
Victor,
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Dwight Mattix
Sent: Wednesday, September 19, 2012 3:43 PM
To: [log in to unmask]
Subject: Re: [TN] Broken Vias
once more with feeling....
Cross section.
At 01:36 PM 9/19/2012, Joyce Koo wrote:
>May be your "small expensive friends" should do a thermal shock 5 or
>10 times prior to assembly to eliminate the problem at PWB level. (fly
>probe before and after).
>Good old days, all the high end stuff are pre-screened at batch level
>prior to assemble and "burn-in" thermal shock 10 times prior to ship to
>root out any early failure = usually at developing stage, not MFG
>stage). Exactly try to avoid expensive mistake later, (was replaced
>later by a coupon on pwb with (1) finest feature (2) weakest location
>(3) new features and (4) testable electrically at functional level
>somewhat, not cheap, but cheaper than risk at assembly level). Follow
>the rule of "pay me now and pay me less, or Pay me later and pay me
>more - usually 10X, if not 100X< more with debug FA add on and time
>loss on delivery.
>
>Joyce Koo
>Materials Researcher - Materials Interconnect Lab Research In Motion
>Limited
>Office: (519) 888-7465 79945
>Mobile: (226) 220-4760
>
>-----Original Message-----
>From: TechNet [mailto:[log in to unmask]] On Behalf Of Robert Kondner
>Sent: Wednesday, September 19, 2012 3:41 PM
>To: [log in to unmask]
>Subject: Re: [TN] Broken Vias
>
>Amol,
>
> Good Questions, I will find out.
>
>Thanks,
>Bob K.
>
>-----Original Message-----
>From: TechNet [mailto:[log in to unmask]] On Behalf Of Amol Kane
>(Asteelflash,US)
>Sent: Wednesday, September 19, 2012 3:30 PM
>To: [log in to unmask]
>Subject: Re: [TN] Broken Vias
>
>Were the boards moisture baked before assembly? .....is the stackup
>balanced? Is the via damage more pronounced in the area of warpage?
>
>
>Amol Kane
>Process Engineer
>AsteelFlash US East Corp
>Tel: (607) 687.7669 x349 (O)
>www.asteelflash.com
>
>
>ITAR Confidentiality Notice: This e-mail and any attachments are
>confidential. It is intended for the recipient only. Prior to
>forwarding this e-mail or opening any attachments please note that they
>may contain security sensitive, proprietary, or export restricted
>information. Any unauthorized disclosure, use, dissemination, or
>copying is strictly prohibited and may be unlawful. Furthermore, this
>communication may contain technical information that is subject to U.S.
>Export Control Laws, including the International Traffic in Arms
>Regulations (ITAR) or the Dept. of Commerce Export Administration
>Regulation (EAR). If so, transfer to a foreign national or
>representative of a foreign government or interest, even in the U.S.,
>without prior Government authorization is prohibited and violation of such Export Control Laws is subject to significant penalties.
>If you received this e-mail in error, please immediately notify the
>sender by replying to this e-mail and delete the e-mail and all copies
>from your computer. Although the sender and Asteelflash have taken
>every reasonable precaution, the e-mail and attachments may have some
>errors or omissions and may contain viruses. We cannot accept liability
>for any damage that you sustain as a result of that
>
>
>-----Original Message-----
>From: TechNet [mailto:[log in to unmask]] On Behalf Of Robert Kondner
>Sent: Friday, September 14, 2012 5:02 PM
>To: [log in to unmask]
>Subject: Re: [TN] Broken Vias
>
>Hi,
>
> Does anyone know about the TCE of via plug material? I am trying to
>get a material number of what was used. This was the first board we
>ever ran with via plugging but I would think that is a well-known process?
>
>Bob K.
>
>-----Original Message-----
>From: TechNet [mailto:[log in to unmask]] On Behalf Of Jason Zhao
>Sent: Friday, September 14, 2012 12:52 PM
>To: [log in to unmask]
>Subject: Re: [TN] Broken Vias
>
>Bob,
>
>Xsection will show you where the opens occur. Possibilities are: copper
>plating folds; thin copper; corner crack; post separation; separation
>due to no wraparound; etc. Then we can determine the root causes from
>there (there are too many to guess now). Looking forward to some pictures.
>
>Best Regards
>
>Jason Zhao
>VP of North America Operations
>Sunshine Circuits
>3400 Silverstone Drive, Suite 139, Plano, TX 75023 US Cell
>510-468-4412, China Cell 131-62722392 www.sunshinepcbgroup.com
>
>-----Original Message-----
>From: TechNet [mailto:[log in to unmask]] On Behalf Of Robert Kondner
>Sent: Friday, September 14, 2012 10:18 AM
>To: [log in to unmask]
>Subject: [TN] Broken Vias
>
>Hi,
>
>
>
>A small company in the area has a board with two very expensive parts,
>about $3K each part. They built 30 boards and had lots of open via connections.
>They are getting cross sections now on some bad vias. In addition to
>many bad vias there was some board warp. Sorry I don't have any hard
>numbers on bad via counts or warp.
>
>
>
>These were 10 mil holes in .062 material, a 6:1 aspect ratio, should be
>easy. Vias were plugged and plated so they could be used as flying
>probe test points.
>
>
>
>After reflow assembly the boards were run on a wave machine using a
>mask where about 25% of the board was exposed to the wave. Everything lead free.
>
>
>
>Question:
>
>
>
>Can folks suggest lists of items we can check, measure or inquire into?
>Any guesses or ideas as what might be going on?
>
>
>
>Thanks,
>
>Bob K.
>
>
>
>______________________________________________________________________
>This email has been scanned by the Symantec Email Security.cloud service.
>For more information please contact helpdesk at x2960 or
>[log in to unmask]
>______________________________________________________________________
>
>
>______________________________________________________________________
>This email has been scanned by the Symantec Email Security.cloud service.
>For more information please contact helpdesk at x2960 or
>[log in to unmask]
>______________________________________________________________________
>
>
>______________________________________________________________________
>This email has been scanned by the Symantec Email Security.cloud service.
>For more information please contact helpdesk at x2960 or
>[log in to unmask]
>______________________________________________________________________
>
>______________________________________________________________________
>This email has been scanned by the Symantec Email Security.cloud service.
>For more information please contact helpdesk at x2960 or
>[log in to unmask]
>______________________________________________________________________
>
>
>______________________________________________________________________
>This email has been scanned by the Symantec Email Security.cloud service.
>For more information please contact helpdesk at x2960 or
>[log in to unmask]
>______________________________________________________________________
>
>---------------------------------------------------------------------
>This transmission (including any attachments) may contain confidential
>information, privileged material (including material protected by the
>solicitor-client or other applicable privileges), or constitute
>non-public information. Any use of this information by anyone other
>than the intended recipient is prohibited. If you have received this
>transmission in error, please immediately reply to the sender and
>delete this information from your system. Use, dissemination,
>distribution, or reproduction of this transmission by unintended
>recipients is not authorized and may be unlawful.
>
>______________________________________________________________________
>This email has been scanned by the Symantec Email Security.cloud service.
>For more information please contact helpdesk at x2960 or
>[log in to unmask]
>______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|