Subject: | |
From: | |
Reply To: | |
Date: | Mon, 2 Apr 2012 20:08:12 +0000 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
You guys are all bad!! (in a good way).
Actually the bread should be cheap white bread (thinking Wonder Bread) so it will break down faster than say whole wheat.
Gregg
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard D.
Sent: Monday, April 02, 2012 12:58 PM
To: [log in to unmask]
Subject: Re: [TN] NTC- unmeltable solder
It depends on which oven is going to be used to bake it.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Robert Kondner
Sent: Monday, April 02, 2012 2:56 PM
To: [log in to unmask]
Subject: Re: [TN] NTC- unmeltable solder
For electronics does the bread need to be lead free?
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Inge Hernefjord
Sent: Monday, April 02, 2012 3:49 PM
To: [log in to unmask]
Subject: Re: [TN] NTC- unmeltable solder
Mother's pride or what kind?
Inge
On 2 April 2012 12:38, Gerald Bogert
<[log in to unmask]>wrote:
> April 2, 2012
>
> The problem may not have anything to do with the solder used. The pipe
> could have some water remaining in it or a valve upstream of where you
> are soldering could have small leak. Any amount of water leak can
> make it difficult if not impossible to make a solder joint. Old
> plumbers trick by putting small piece of bread into the pipe may stop
> the leak long enough to make the solder joint.
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of David D. Hillman
> Sent: Thursday, March 29, 2012 4:57 PM
> To: [log in to unmask]
> Subject: Re: [TN] NTC- unmeltable solder
>
> Hi Blair - one other possible reason but lower on the possibility
> scale is that the solder joint, if old enough, had converted itself
> into a tin/copper joint rather than copper and solder joint. Most
> solders contain a low melting element - i.e. lead, bismuth, etc. - so
> the solder joints should go molten but if you had a high tin alloy
> with minimal lower melting point element addition, you would be trying
> to
"melt"
> copper/tin intermetallic which isn't going to happen. Mike's or
> Chuck's responses are more probable explanations for what you experienced.
>
> Dave
>
>
>
> Blair Hogg <[log in to unmask]>
> Sent by: TechNet <[log in to unmask]>
> 03/29/2012 12:20 PM
> Please respond to
> TechNet E-Mail Forum <[log in to unmask]>; Please respond to
> Blair Hogg <[log in to unmask]>
>
>
> To
> <[log in to unmask]>
> cc
>
> Subject
> [TN] NTC- unmeltable solder
>
>
>
>
>
>
> The recent discussions on rework issues reminded me of a while back
> where I needed to repair a leaky water pipe in my home. Took a chunk
> of the ceiling out, got out the plumbers torch, drained the pipes and
> started to heat. No matter what I did to the joint that was leaking I
> could not get
>
> anything to melt. Had to cut the pipe on either side of the elbow
> joint and patch in a new section. Even afer I took it out I could not
> get it apart. Not sure what happened to the solder but something
> changed it to make it unmeltable.
>
> Blair
>
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud
> service.
> For more information please contact helpdesk at x2960 or
> [log in to unmask]
> ______________________________________________________________________
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or
> [log in to unmask]
> ______________________________________________________________________
>
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask] ______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
|
|