Sender: |
|
X-To: |
|
Date: |
Mon, 23 Apr 2012 10:52:01 -0400 |
Reply-To: |
|
Message-ID: |
<OFC9BCE039.D157239F-ON852579E9.00512210-852579E9.0051A4B9@LocalDomain> |
Subject: |
|
From: |
|
Content-Type: |
text/plain; charset="ISO-8859-1" |
In-Reply-To: |
|
Content-Transfer-Encoding: |
quoted-printable |
MIME-Version: |
1.0 |
Parts/Attachments: |
|
|
pH paper slightly dampened with DI water. I've used it and it works.
Some of the organic acid activators will be left behind after soldering,
but most of them should have sublimed during processing. Additionally, some
organic acids are worse than others; malic is worse than succinic is worse
than adipic.
Karen Tellefsen - Electrical Testing
[log in to unmask]
908-791-3069
Re: [TN] No-Clean Flux
Robert Kondner
to:
TechNet
04/23/2012
10:43 AM
Sent by:
TechNet <[log in to unmask]>
Please respond to rkondner
Hi,
Are there any spray on chemical indicator that can be used to detect for
activated flux? Something like a litmus or phenolphthalein solution?
Bob K.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Brian Ellis
Sent: Monday, April 23, 2012 10:28 AM
To: [log in to unmask]
Subject: Re: [TN] No-Clean Flux
I agree 100% with Doug. The important point is to ensure that the
carboxylic acids are sublimed. This starts to happen at temperatures around
180°C but it takes time as well as temperature. It is therefore essential
to limit the quantity to the minimum necessary to do the job and confine to
the joint area. What is positive is that soldering irons operate at a
higher temperature than wave or reflow, so that residues that spread
outside the joint area will probably be heated sufficiently to ensure
sufficient sublimation. Another important point is to ensure that all the
alcohol has evaporated before starting the retouch, so that the latent heat
of evaporation would otherwise cool down the flux and allow it to spread
before sublimation takes place. This requires the operator to wait a few
minutes between dosing the flux and picking up the soldering iron. It is
common to have a row of fluxed assemblies and, as one is added at one end,
a circuit is picked up at the other end for soldering. I don't know whether
it is still available, but a flux with a crimson dye showed where unheated
flux was applied and was quite common in days of yore. The dye sublimated
with the activators.
Brian
On 23/04/2012 16:42, Woolley, Mark D. (Mark) wrote:
> I have an issue with one of the assembly houses we use. They are
> using a No-clean flux that contains adipit and succinic acids (per the
> MSDS) in an alcohol base.
>
> Is it allowed to leave flux on the PWB that HAS NOT BEEN DEACTIVATED
> BY HIGH TEMPERATURES OF SOLDERING?
>
> I am not talking about the flux used in the solder paste or wave
> soldered flus. I am talking about the flux used at rework and
> touch-up of the PWB.
>
>
>
> I havce seen papers detailing corrosion on PWBs using "no-clean"
> fluxes and I have seen it on some of our products. This usually
> pccurs near the periphery of the PWB where the wave solder flux is
> protected by the pallet used to pass the PWB through the solder wave.
>
>
>
> Any opinions and references will be appreciated. I can give the
> manufacturer and flux type to individuals, but don't want to put it in
> a global email.
>
>
>
> Thanks
>
> mark
>
>
>
>
>
> mark
>
> Mark Woolley |PTRL Laboratory | Avaya | 1300 West 120th Ave |
> Westminster, CO 80234 USA |
>
> Voice (Lab): (303) 538-2166 | email: [log in to unmask] |
>
>
>
>
> ______________________________________________________________________
> This email has been scanned by the Symantec Email Security.cloud service.
> For more information please contact helpdesk at x2960 or
> [log in to unmask]
> ______________________________________________________________________
>
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
|
|
|