George,

The silver sulfide corrosion was verified by using SEM, EDS and FTIR. We 
had a test lab make this analysis. The corrosion causes a change in the 
resistor value and eventually an open. This causes our equipment to fail 
of course. This is an environmental issue local to a particular customer 
or area. This determination is based on the fact that this is the only 
place where we see these issues and also based on what we know about the 
local air quality.


On 5/25/2011 8:37 AM, Wenger, George M. wrote:
> Leif Erik,
>
> When you indicate that you confirmed the failure due to silver sulfide do you mean that you can see silver migration or silver sulfide corrosion products shorting features or corrosion causing an open circuit?  I couldn't tell from your email if the exposed silver on the resistor network was corroding and causing an open circuit or if silver had migrated causing a short circuit.  It is not uncommon to see tarnish and or silver sulfide corrosion on products with exposed silver.  However, the only failures we've seen were primarily due to ionic residues left behind from assembly processes causing creep corrosion.  When residues aren't present we still see various degrees of silver sulfide on silver surfaces from a light tarnish to a heavy Brown/Black appearance depending on the amount of air pollution and exposure time but no migration or detrimental corrosion.
>
> Regards,
> George
> George M. Wenger
> Senior Principal Reliability / FMA Engineer
> Andrew Corporation - Wireless Network Solutions
> 40 Technology Drive, Warren, NJ 07059
> (908) 546-4531 Office (732) 309-8964 Mobile
> E-mail: [log in to unmask]
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Leif Erik Laerum
> Sent: Wednesday, May 25, 2011 9:12 AM
> To: [log in to unmask]
> Subject: [TN] Silver Sulfide contamination
>
>    Technetters,
>
> We have confirmed that a returned product from the field has failed die
> to silver sulfide contamination.
>
> The conclusion from the analysis is:
> Based on the analysis performed, the "black" contaminant material is
> silver sulfide, a common silver corrosion product. This corrosion often
> occurs when silver plating is exposed to atmospheric pollution that
> contains high levels of sulfur compounds (exhaust from fossil fuels).
>
> We have confirmed that in particular resistor networks are susceptible
> due to the silver content that apparently is exposed on the top of the
> component. We have not observed issues with any other component types.
>
> The obvious answer to how to protect a product in this environment is to
> use conformal coating. However, from what I have read there are only
> very few coating materials that can actually protect from silver sulfide
> corrosion. Epoxy based conformal coatings is the only ones that will
> successfully pass ASTM N 809 test. My question to the experts is if
> there are other solutions or coatings you have been successful with or
> if someone has actually solved this issue in different ways. It seems
> this should be an important issue for the automotive electronics industry.
>
> Some one suggested using solder to cover the component, but I can not
> understand how that could work.
>
> As always, thank you for your insight.
>


CONFIDENTIALITY NOTICE: This email and any attachments are Texas Memory Systems' proprietary material for the exclusive and confidential use of the intended recipient.  If you are not the intended recipient, please do not read, distribute or take action in reliance upon this message. Any unauthorized disclosure is prohibited.  If you have received this in error, please notify us immediately by return email and promptly delete all copies of this message and its attachments from your computer system. 



______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask] 
______________________________________________________________________

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 16.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
For additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------