Sender: |
|
X-To: |
|
Date: |
Fri, 20 May 2011 18:14:59 +0000 |
Reply-To: |
|
Message-ID: |
|
Subject: |
|
From: |
|
MIME-Version: |
1.0 |
In-Reply-To: |
|
Content-Transfer-Encoding: |
quoted-printable |
Content-Type: |
text/plain; charset="us-ascii" |
Parts/Attachments: |
|
|
Arlene,
I too have used +/-10% for PCB finished thickness tolerance for the past 25 years. That was passed down to me from the PCB manufacturer's that I have used.
The IPC-2221A section 5.4.1 "Dimensions and Tolerances" refers to the new IPC-2615 for Geometric Dimensioning and Tolerancing (GDAT). Unfortunately I have most of the 2610 series except 2615, so I can't verify if what you're looking for is in there, but here is the list for the IPC-2610 series -
IPC-2611 - Generic Specification
IPC-2611 - Generic Requirements for Electronic Product Documentation
IPC-2612 - Sectional Requirements for Electronic Diagramming Documentation (Schematic and Logic Descriptions)
IPC-2613 - Sectional Requirements for Assembly Documentation (Electronic Printed Board and Module Assembly Descriptions)
IPC-2614 - Sectional Requirements for Board Fabrication Documentation (Printed Circuit board Description Including Embedded Passives)
IPC-2615 - Sectional Requirements for Dimensions and Tolerances
IPC-2616 - Sectional Requirements for Electrical and Mechanical Part Descriptions (Specification and Source Control Part Descriptions)
IPC-2617 - Sectional Requirements for Discrete Wiring Documentation (Wire harness, Point to Point and Flexible Cable Descriptions)
IPC-2618 - Sectional Requirements for Bill of Material Documentation (Complete Listing of Parts, Materials, and Procurement Documents)
Tom
-----Original Message-----
From: DesignerCouncil [mailto:[log in to unmask]] On Behalf Of Arlene Fox
Sent: Friday, May 20, 2011 10:04 AM
To: [log in to unmask]
Subject: [DC] PCB thickness standard
Hi all,
Can somebody point me to the IPC standard that defines the tolerance for a pcb's finished thickness? I always use +/- 10% but I haven't been able to locate the standard.
Thanks
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 16.0.
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
For additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 16.0.
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
For additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
|
|
|