Thank-you Wayne for pointing out these details. I will take a look at
the bonding process again.
I have uploaded the wire bond configuration in the file cabinet.
http://ipc-technet.groupsite.com/main/summary
Mumtaz Bora
Senior Packaging Engineer
Peregrine Semiconductor
9380 Carroll Park Drive
San Diego, CA 92121
858-795-0112-direct
858-731-9499 -fax
[log in to unmask]
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Thayer, Wayne - IIW
Sent: Saturday, November 13, 2010 4:36 AM
To: [log in to unmask]
Subject: Re: [TN] Wire Bond Pull failures
The picture of bond 22 is the only picture where I see a loop. The
lead-in angle for the loop looks pretty high. I suspect all of the
failed bonds have similar angles.
Aluminum is great for ultrasonic welding but it is very brittle, so it
is hard to get everything right. The brittleness manifests itself in
heel cracks at the first bond, which is what you show here. The high
lead-in indicates that the wire was likely worked pretty hard during
loop formation. Furthermore, the intact bond looks like a crack has
started.
The pictures show several other noteworthy items/contributors:
-The tails are all extremely even. This, and the lack of a visible back
radius nick in the wire loop, suggests a "clamp tear" style bonder
instead of "table tear" (used for deep access tools). These tails are
even despite what looks like a lot of material deformation during the
tail formation process. Also, the position of the wires on the pads are
very precise. So I think the bonder itself and operator must be pretty
high quality.
-The tails are way too short for my taste. I like to see at least 1
wire diameter of tail (you have about half that). All of the techs who
develop programs can't resist cranking that tail down as low as it will
go to show off what a great machine they have. But if you think about
the danger in significant changes to the weld dynamics when the loop
gets too short, you'll conclude a bit of tail is a very good thing.
-The wire deformation at the bond site is a bit on the high side. This
is a big contributor to the heel cracks mentioned above.
To fix the problem, have your operator try to get a bit less first bond
deformation and design a loop profile which doesn't stress the wire as
much. If that doesn't get the job done, then you may have the wrong
radii on your bonding tool, or you are trying to force the wrong loop
into the aluminum. Also, as I indicated above, bring the tails out to 1
wire diameter so we're not trying to weld in the work hardened zone.
Wayne Thayer
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Mumtaz Bora
Sent: Friday, November 12, 2010 9:15 PM
To: [log in to unmask]
Subject: [TN] Wire Bond Pull failures
Hello TechNetters,
I have some wirebonds on a Hi -Rel package that pulled below 2.0 gm
minimum per Mil -Std -883. I have taken some SEM images of failed and
good bonds. Customer has a concern with plane of fracture of the failed
bonds even though it is break at "neck" . . It is Aluminum wire/to
Aluminum bond pad wedge bonded ultrasonically and aluminum wire to gold
plated post also bonded ultrasonic. Wire pull is post seal. I have
uploaded the file of images on the TechNet groupsite .I will appreciate
some feedback from wirebonding experts on the forum.
http://ipc-technet.groupsite.com/main/summary
<http://ipc-technet.groupsite.com/main/summary>
Thank-you, Mumtaz
Mumtaz Bora
Senior Packaging Engineer
Peregrine Semiconductor
9380 Carroll Park Drive
San Diego, CA 92121
858-795-0112-direct
858-731-9499 -fax
[log in to unmask]
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or
[log in to unmask]
______________________________________________________________________
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
This e-mail and any files transmitted with it may be proprietary and are
intended solely for the use of the individual or entity to whom they are
addressed. If you have received this e-mail in error please notify the
sender.
Please note that any views or opinions presented in this e-mail are
solely those of the author and do not necessarily represent those of ITT
Corporation. The recipient should check this e-mail and any attachments
for the presence of viruses. ITT accepts no liability for any damage
caused by any virus transmitted by this e-mail.
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or
[log in to unmask]
______________________________________________________________________
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
