Ed,

We had a couple of fancy bottom drills when I worked at Fortin.  We
spot-faced down to the inner layer targets then used these drills made in
Switzerland to drill the center of the target.  The customer used that for
set up tooling and could drill with these.

I want to say the manufacturer was Posalux.




Posalux, Microhole technologies, PCB drilling and routing ...
Posalux, Microhole technologies, PCB drilling and routing, Jewellery
faceting and engraving, Switzerland.
www.posalux.net/microfor/e/ - Similar


Chuck Brummer
3M Manufacturing Engineer
8357 Canoga Ave.
Canoga Park, CA 91304-2605
(818) 734-4930




From:
Ed Popielarski <[log in to unmask]>
To:
[log in to unmask]
Date:
07/01/2010 02:44 PM
Subject:
[TN] Bombsite PCB drill
Sent by:
TechNet <[log in to unmask]>



Hi fellow 'netters,

I took a job up here in the Silicon Valley. I've been lurking, but not
participating much. I must say, it's good to be back!

I've been looking for an old school pcb drill, bottom up configuration
with a magnified bombsite optical alignment, typically was used for
homebrewed prototypes.

I've scoured the www and cannot find a current manufacturer.

If you might have one (or know where one is) I'm very interested.

Any help would be appreciated!


Regards,

Ed Popielarski

Sr. Mfg. Engr.


NBS Corporation
2950 Patrick Henry Dr.
Santa Clara, Ca. 95054

Ph: 408-654-1100
Fx: 408-654-1107
Cl: 408-234-1497
Cl: 949-581-6601



______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------





______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------