Subject: | |
From: | |
Reply To: | |
Date: | Wed, 16 Jun 2010 22:54:04 +0200 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Thanks Wayne.
1. No aspect on 'half moon crescent' ?
2. Have you or someone else practised Manson's universal slope equation
for calculation of life expectancy of bond wires?
Delta epsilon = 3.5 x sigma b/E x Nf exp-0.12 + epsilon1 exp 0.6 x Nf
exp -0.6
where
Delta epsilon = elongation
sigma b = rupture tension
E = elasticity module
Nf = number of cycles to rupture
epsilon1= rupture elongation
We used this for deciding how many cycles gold wires would withstand in a
typical MIL aircraft application when the substrates were alumina and the
packages Kovar. The result was som 50,000 - 100,000 cycles or 60-120 years
for -55/+125C.
The question is how much one can rely on this calculation model. Anyone
done similar ? Personally I thing one should only see such calculations as
estimations only.
Inge
--------------------------------------------------
From: "Thayer, Wayne - IIW" <[log in to unmask]>
Sent: den 16 June 2010 20:57
To: <[log in to unmask]>
Subject: Re: [TN] ?
> Hi Inge!
>
> 5 grams per square mil average shear for gold ball bonding
> Avg - 3 x StdDev > 3 grams for 1 mil gold destructive pull test
>
> The latter is kind of vague because the wire set must be large enough to
> get a good sample size and all of the loops have to have reasonable
> heights and must be similar.
>
> For aluminum, we're very application-dependent, but use the Avg - 3 x
> StdDev as the parameter of interest.
>
> These don't test how close to cratering we are, which is an industry-wide
> issue.
>
> Visually, we are looking for a consistent rim on the ball, and a rim
> height no greater than about one half of the wire diameter. For the
> stitch, consistency and virtually no capillary imprint from the stitch
> process on the lead/land.
>
> Wayne
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Inge
> Sent: Wednesday, June 16, 2010 1:58 PM
> To: [log in to unmask]
> Subject: [TN] ?
>
> What standards do you use for inspection and qualification of wire bonding
> today?
> Thanks
> IInge
>
>
> ______________________________________________________________________
> This email has been scanned by the MessageLabs Email Security System.
> For more information please contact helpdesk at x2960 or [log in to unmask]
> ______________________________________________________________________
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet
> To temporarily halt or (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL)
> To receive ONE mailing per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at: http://listserv.ipc.org/archives
> Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
> for additional information, or contact Keach Sasamori at [log in to unmask] or
> 847-615-7100 ext.2815
> -----------------------------------------------------
>
> This e-mail and any files transmitted with it may be proprietary and are
> intended solely for the use of the individual or entity to whom they are
> addressed. If you have received this e-mail in error please notify the
> sender.
> Please note that any views or opinions presented in this e-mail are solely
> those of the author and do not necessarily represent those of ITT
> Corporation. The recipient should check this e-mail and any attachments
> for the presence of viruses. ITT accepts no liability for any damage
> caused by any virus transmitted by this e-mail.
>
> ______________________________________________________________________
> This email has been scanned by the MessageLabs Email Security System.
> For more information please contact helpdesk at x2960 or [log in to unmask]
> ______________________________________________________________________
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0
> To unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet
> To temporarily halt or (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL)
> To receive ONE mailing per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at: http://listserv.ipc.org/archives
> Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
> for additional information, or contact Keach Sasamori at [log in to unmask] or
> 847-615-7100 ext.2815
> -----------------------------------------------------
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|