Sender: |
|
X-To: |
|
Date: |
Tue, 16 Feb 2010 14:52:19 -0600 |
Reply-To: |
|
Subject: |
|
MIME-Version: |
1.0 |
Content-Transfer-Encoding: |
quoted-printable |
Content-Type: |
text/plain; charset="us-ascii" |
From: |
|
Parts/Attachments: |
|
|
This won't directly measure the air gap but it will tell you the
compression seen across the mating surfaces.
www.pressurex.com
Regards,
Mike
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Joe Macko
Sent: Tuesday, February 16, 2010 2:34 PM
To: [log in to unmask]
Subject: [TN] Best way to measure "actual" themal pad compression
All,
I am looking for some proven ways to measure the actual air gap (e.g., 5
to 30 mils) between a component and its mating thermal pad pedestal
located on a Chassis without cutting up the hardware so I can determine
the actual thermal pad compression once a pad is installed. Using a
model, the theoretical gap can be calculated but I would like to
empirically measure/verify what the gap is and the subsequent pad
compression. Visually, it is hard to tell and not all locations are
visible and, I do not have access to any hardware to cut up, etc.. so I
am looking for a tried and proven method. Some have suggested using a
soft material like putty that will compress and could then be
subsequently measured after disassembly. I have heard rumors of material
designed for this purpose but are unable to find such material. thx
Best Regards,
-Joe M.
"This e-mail and any attachments are solely for the use of the addressee
and may contain L-3 proprietary information that may also be defined as
U.S. Government export controlled technical data. If you are an
unintended recipient of this e-mail, use, disclosure or distribution of
its content is prohibited. Please notify the sender by return e-mail and
immediately delete this message."
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or
[log in to unmask]
______________________________________________________________________
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please contact helpdesk at x2960 or [log in to unmask]
______________________________________________________________________
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|