TECHNET Archives

December 2009

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Robert Kondner <[log in to unmask]>
Reply To:
Date:
Tue, 8 Dec 2009 14:48:19 -0500
Content-Type:
text/plain
Parts/Attachments:
text/plain (155 lines)
Hi,

 They are NOT conductive. They are good insulators.

 There are zillions of different types available, I bought some from Digikey
or Mouser.

Bob Kondner

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Paul Edwards
Sent: Tuesday, December 08, 2009 2:35 PM
To: [log in to unmask]
Subject: Re: [TN] Looking for guidance on V-Score requirements

Bob,

Just out of curiosity where are you getting those conductive or
semi-conductive "stick-on-rubber feet"?

Paul 

Paul Edwards
Surface Art Engineering


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Robert Kondner
Sent: Tuesday, December 08, 2009 7:39 AM
To: [log in to unmask]
Subject: Re: [TN] Looking for guidance on V-Score requirements

Ken,

  Getting thin, partially routed boards for stuffing is not uncommon. Pick
and Place machines (PnP) generate considerable force when they place a part.
What I do, and probably most others, is place the thin material on a
carrier. This problem with parts on both sides requires a fixture of some
type to support the thin board leaving space for bottom side parts.

 We take a piece of FR4 and we create a 1:1 (close is fine) paper image of
the bottom side. A mirror of the silk image is often fine. Place the paper
on the FR4 using a low tack spray adhesive. Now you can take "Stick On
Rubber Feet" and cut them placing these as fixed height spacers which hold
the thin board slightly above the FR4 carrier. 

 The other option is use the tooling pins that come with your PnP machine
though this board had a lot of smaller boards. You still need to control the
placement of the holding magnets so the mirror image print is a help.

 There are many creative ideas and tools you can purchase to solve these
problem. I use the cut up sticky rubber feet.

Bob Kondner

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Ken Bloomquist
Sent: Tuesday, December 08, 2009 10:10 AM
To: [log in to unmask]
Subject: Re: [TN] Looking for guidance on V-Score requirements

Hi bob,

I'm trying to understand what you are saying but I can't figure it out.
Could you please go into a tiny bit more detail for me? "Rubber Feet"?

Thanks,

KennyB
-----Original Message-----
From: Robert Kondner [mailto:[log in to unmask]] 
Sent: Tuesday, December 08, 2009 7:17 AM
To: [log in to unmask]
Subject: Re: [TN] Looking for guidance on V-Score requirements

If only one side has parts then there is no problem. If you have parts on
two sides then a holder can easily be made with cut up "Rubber Feet".
However both the holder and the board must be held steady and this varies
with the assembly machine.

Bob Kondner


---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------


 ===========================================================================
==

This email and any attachments thereto may contain private, confidential,
and
privileged material for the sole use of the intended recipient. Any review,
copying,
or distribution of this email (or any attachments thereto) by others is
strictly prohibited.
If you are not the intended recipient, please contact
[log in to unmask]
immediately and permanently delete the original and any copies of this email
and
any attachments thereto. 

 ===========================================================================
==


---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2