Subject: | |
From: | |
Reply To: | |
Date: | Mon, 14 Dec 2009 16:19:54 +0000 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
I agree with Guy, incorporating all the fabrication info in 610 would
make it an unwieldy document, so backtracking to 600 for a fabrication
defect found after assembly is perfectly reasonable.
Regards
Ian Fox
Lead Materials and Process Engineer
Aero Engine Controls
A Rolls-Royce plc and Goodrich Corporation Joint Venture
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Guy Ramsey
Sent: 14 December 2009 15:41
To: [log in to unmask]
Subject: Re: [TN] Acceptability of Shredded Board Edge
The section in the 610 that addresses this is edge delamination. Is it
inadequate?
I would say you can use the 600 spec even after assembly. The assembly
is a populated defect.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Jack Olson
Sent: Monday, December 14, 2009 10:22 AM
To: [log in to unmask]
Subject: [TN] Acceptability of Shredded Board Edge
Greetings!
We have an assembly where the board edge was ripped badly during
depanelization.
I searched through the Assembly Acceptability IPC-A-610 and didn't find
much, but in the bare board IPC-A-600 section 2.1, I can see plainly
that ours is rejectable.
The question is, can I use the BARE BOARD spec to reject an ASSEMBLY?
Or is there anything in the assembly specs that covers depanelization
damage?
thanks,
Jack
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing
per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or 847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
--------------------------------------------------------------------------
This message (and any attachment) is confidential and is intended for the named recipient only.
If you receive it in error please e-mail back the sender and permanently delete the original message and any copies.
Rolls-Royce Goodrich Engine Control Systems Limited.
Registered Office: Moor Lane, PO Box 31, Derby, DE24 8BJ.
Registered in England No. 06686268.
--------------------------------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|