Hi Steve - my experience matches yours! If you don't go slow, use good
equipment and have well understood cutting materials, bad things (like
microcracks) can happen.
Dave
Steven Creswick <[log in to unmask]>
Sent by: TechNet <[log in to unmask]>
11/25/2009 10:37 AM
Please respond to
TechNet E-Mail Forum <[log in to unmask]>; Please respond to
Steven Creswick <[log in to unmask]>
To
[log in to unmask]
cc
Subject
Re: [TN] Preparing for microvia examination
Inge,
My observations when sectioning LED's, and Si devices was that I could
make
problems if I rushed the process too quickly.
I always go very slowly. I don't rush the cut. Don't rush the polishing
operation. Go slowly! If I rush the cutting or polishing, I frequently
end
up with cracks, chip-outs, etc.
If you were working with unpackaged [Flip Chips], I would suggest that you
may also wish to visualize the stress that the potting material puts on
your
chips.
It may also be possible for your potting material to induce enough stress
inside a packaged device too, but I might not put that very high on my
likelihood list. It seems that the cohesive strength of the Si is greater
than the interfacial strength between the Si and the mold compound.
I have not seen it inside packaged devices, but can acknowledge its
possibility - Can you afford to look at a part using reflected acoustics?
If you could 'safely' get a chip off the board without causing more
damage,
one could look at it in a through-transmission mode. If the separation
were
as gross as you indicate, it should show up very easily with a low freq
transmission mode transducer.
Another option may be to do some fine focus x-ray examination of the board
and suspect vias to satisfy yourself of their integrity, then sacrifice
the
IC by chemical de-encapsulation processes..
I've only seen device cracks like you describe when large CTE's/and or
thermal excursions were involved - [eg - power MOSFET soldered on Cu and
power cycled to death, or large chips using unfilled (optical) molding
compounds].
You have all the fun parts!
Steve C
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Inge
Sent: Wednesday, November 25, 2009 11:03 AM
To: [log in to unmask]
Subject: [TN] Preparing for microvia examination
Schrekxscht!
That was the way the aliens from planet Mars saluted us in the funny film
that ended in their heads exploding when a guy played Elvis Presley on his
car radio. What does that have to do with microvias? Anyone with
experience
from cutting a board into small pieces and mold them in epoxy for cross
section analysis? I use a thin blade, high rpm diamond blade for cutting.
The board was equipped with SuperBGAs down to smallest QFNs. We suspected
via problems and looked for such after polishing. In fact we found
extremly
good barrels and no sign of via issues. Instead we saw that some
cross-sectioned semi chips had fine microcracks. In some cases, the
microcrack ran all the way across the chip, i.e. the whole active area was
more or less separated from the rest of the chip.My q is this: has anyone
of you got microcracks in the semi chips caused during the cutting
operation? I,ve cross sectioned hundreds of boards during my time here,
but
never seen cracks like these be caused by the diamond cutting. Can there
be
a Schrekxscht when you use the diamond saw?
/Inge
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|