I had not thought about using it to cure underfill. That is an excellent
idea. Thanks, Dave!
dean
R. Dean Stadem
Consulting Engineer
Analog Technologies Corp./Lumagine, Inc.
11441 Rupp Drive
Burnsville, MN 55431
(952)894-9228
[log in to unmask]
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of David D. Hillman
Sent: Thursday, September 03, 2009 1:57 PM
To: [log in to unmask]
Subject: Re: [TN] Hakko FR-802
Hi Richard! We have the FR1012 preheater to be extremely useful - very
adaptable, rugged and can be used for a wide array of preheating
challenges (works really well in the underfill processes). No more
burning
your hands/wrists on the edges of a hot plate.
Dave Hillman
Rockwell Collins
[log in to unmask]
"Stadem, Richard D." <[log in to unmask]>
Sent by: TechNet <[log in to unmask]>
09/03/2009 12:32 PM
Please respond to
TechNet E-Mail Forum <[log in to unmask]>; Please respond to
"Stadem, Richard D." <[log in to unmask]>
To
[log in to unmask]
cc
Subject
Re: [TN] Hakko FR-802
We have a customer who does not allow a solder iron to touch any
leadless
ceramic chip capacitor, resistor, glass-bodied diode, etc. (for very
good
reasons). To facilitate rework or touchup of these components, we just
purchased an Hakko FR-802 Digital hot air rework station and, more
importantly, the Hakko FR-1012B infrared pre-heater system. This
combination allows us to easily rework any component on any CCA, no
matter how massive. Although we do have two Airvac DRS24 stations and
other rework stations, we really like the Hakko system for quick and
easy
manual hot gas rework of smaller components. The pre-heater is
fantastic,
it easily heats any CCA and makes the rework simple and easy, even for
massive metal-clad CCAs.
The preheater has a built in CCA holder and it operates with a
thermocouple taped to the PWB to bring the CCA temp up to a pre-set
temperature, then shuts off and idles to hold the PWB at just that
temperature, +-3 deg. C. We never increase the heat setting on the wand,
if we need more heat we just bump up the pre-heater by 10 degrees or so.
All of our rework can be done with the pre-heater set to between 90 to
120
deg. C.
Fantastic system, much better than the others I evaluated. Be sure to
get
the pre-heater, it really makes all the difference in the world. Get the
1012B, not the 1012, as the B model allows you to turn on or off any of
the four quadrants of the IR pre-heater.
Can't say enough good things about it.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Ioan Tempea
Sent: Thursday, September 03, 2009 12:11 PM
To: [log in to unmask]
Subject: [TN] Hakko FR-802
Dear Technos,
I would need your opinion on this hot air rework station.
Thank you,
Ioan Tempea, ing.
Ingénieur Principal Fabrication / Sr. Manufacturing Engineer
30 ans déjà! - 30 years already!
950 rue Bergar, Laval, Québec, H7L 5A1
t : 450-967-7100 ext : 244
Mtl : 514-990-5762
f : 450-967-7444
[log in to unmask] <mailto:[log in to unmask]>
www.digico.cc <http://www.digico.cc/>
P N'imprimer que si nécessaire - Print only if you must
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
