Wayne,
then you must have experienced the law of falling dust under a car.
You lift the car, place secure supports under, crawl under car, rotate 180
degrees to look upwards, got the secure spring in your right hand and lamp
in the other , reaching out a trembling hand to put that darn thing on its
place. Just a millimeter more and then the thing will fit...THEN...not
sooner, nor later...EXACTLY THEN is a microscopic particle falling right
into your staring eye. It has been there for years, just waiting for the
correct time. You make a violent gesture in the direction to your eyes, and
the hand touches a scalpel sharp metal piece. You are now swearing and
crawling back with a speed like a green mamba and when asking friend to find
the timber in your eye, a thought of panic begin to form: the only and one
little secure ring is somewhere on the floor which is covered by 30 years of
oil and debris. And it's Sunday. And you forgot the mobile telephone at
home.
/Inge
----- Original Message -----
From: "Thayer, Wayne - IIW" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Tuesday, July 14, 2009 4:02 PM
Subject: Re: [TN] NTC (It's not Friday, but this is so true!)
Hi Inge!
I am also someone who takes stuff to pieces. You should see the scars on my
knuckles from all of the sheet metal cuts you can get on a car.
Now that you've put your car back together....
Are you absolutely sure the solder joint was bad when it left the line? I
mean, the rest of the joints look just fine, so what is it about that one?
In all liklihood this was wave soldered.
What if the real problem is that too much current is going through that
joint, which is considerably smaller than the adjacent joint on the same
trace? You may have only peeled back the first layer of the onion!
I hate to put doubts in the mind of someone who did an excellent job getting
the thing repaired, but I know you are tough!
Wayne
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Steven Creswick
Sent: Tuesday, July 14, 2009 3:55 AM
To: [log in to unmask]
Subject: Re: [TN] NTC (It's not Friday, but this is so true!)
Inge - wow! It's all in the hunt! Good find!
Steve - You are right! That is a cool trailer!
Steve C
http://stevezeva.homestead.com/files/Inge_s_Car_Fun_.pdf
http://stevezeva.homestead.com/files/Unusual_Trike.jpg
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in the
BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet
NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send
e-mail to [log in to unmask]: SET Technet Digest Search the archives of
previous posts at: http://listserv.ipc.org/archives Please visit IPC web
site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
This e-mail and any files transmitted with it may be proprietary and are
intended solely for the use of the individual or entity to whom they are
addressed. If you have received this e-mail in error please notify the
sender.
Please note that any views or opinions presented in this e-mail are solely
those of the author and do not necessarily represent those of ITT
Corporation. The recipient should check this e-mail and any attachments for
the presence of viruses. ITT accepts no liability for any damage caused by
any virus transmitted by this e-mail.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
