A quick check on vtekusa.com (there are others...) shows a few
possibilities, you may have to put a pick offset due to pocket depth but
a few of these should work out. They should be able to quote it for
you.
Package Type / Device V-TEK P/N Material Type Size Width x Pitch Meters
Per Reel Pockets / Reel Width / Ao Length / Bo Depth / Ko Depth K1
GS71116AGU-7
BG0608 TMT16AV866 SDPS 16X12 78 7885 6.50 8.50 2.10 1.30
SOIC-14B TMT16TPV2108 CPS 16X8 87 10,875 6.50 9.00 2.10 0.00
TSSOP-24 TMT16AV473 SDPS 16 X 8 102 11,250 6.95 8.30 1.60 1.20
TSSOP-24 TMT16TPV1121 CPS 16 X 8 110 13,750 6.70 8.20 1.75 1.45
Audiocode AC482-CBL
BGA-41 TMT24TPV2073 CPS 24X16 60 3720 13.86 12.59 3.22 0.00
BGA-41-A TMT24TPV2074 CPS 24X16 60 3720 12.59 13.86 3.22 0.00
Q10X10 TMT24AV655 SDPS 24 X 16 90 5,270 12.35 12.35 2.20 1.70
QFP10X10 TMT34TPN1786 CPS 24X16 85 5270 12.52 12.52 2.18 1.80
Mike
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Kane, Amol (349)
Sent: Wednesday, June 10, 2009 8:32 AM
To: [log in to unmask]
Subject: [TN] T&R BGA parts
Dear Technetters,
I have been trying to find these BGA parts on T&R (we currently get them
in matrix trays), but have been told that either the manufacturer does
not offer them in T&R or that they cannot be converted to T&R due to
excessive tape cost and horrendous min buys. Any outside chance that any
of you fine folks buy/convert them in T&R?...i would so like to hear
from you if that's the case....offline replies are acceptable too.
GSI Technologies GS71116AGU-7
Audiocode AC482-CBL, 12 x 12 mm2, 144 pin BGA , 0.8 mil, (AC482-CB)
Thanks,
Amol
WARNING: Export Control
This document may contain technical data within the definition of the
International Traffic in Arms Regulations (ITAR), and subject to the
Export
Control Laws of the U.S. Government. Transfer of such data by any means
to a
foreign person, whether in the United States or abroad, without proper
export
authorization or other approval from the U.S. Department of State is
prohibited.
CONFIDENTIALITY NOTICE:
This e-mail, and any attachments, is for the sole use of the intended
recipient(s) and may contain information that is confidential and
protected from disclosure under the law. Any unauthorized review, use,
disclosure, or distribution is prohibited. If you are not the intended
recipient, please contact the sender by reply e-mail, and delete/destroy
all copies of the original message and attachments.
Thank you.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
