Hi John,
The underlying assumption in Eq. 16 is an adequate sample size (32).
What you are doing is not partitioning a component, however, but daisy-chaining components together.
In this case, what you did is correct, because you record the first failed component of 10, and so your eq. should read like this:
Nf(50%,component) = Nf(50%,m daisy-chained components) * [m]^(1/BETA)
= 800 * (10)^1/4
= 1422
Plotting things like this on a Weibull graph typically is very helpful.
Werner
-----Original Message-----
From: Nieznanski, John A - SSD <[log in to unmask]>
To: [log in to unmask]
Sent: Thu, 18 Dec 2008 12:43 pm
Subject: [TN] to apply partition correction on individual daisy chains or not?
Hi TechNet List Gurus,
If I have several different serial daisy chains undergoing accelerated
reliability testing per IPC-SM-785, can I apply partition correction (IPC-SM-785
Eq. 16) to calculate an "effective" Nf @test (X%) for each daisy chain? Each
chain only has a single component type, but there are different numbers of
components in each chain.
For example, if the first chain has 10 two-terminal leadless SMT components
(assume BETA=4), and the first IPC-SM-785 failure occurs at 800 cycles, then per
Eq. 16:
Nf (component) = Nf (m partitions) * [1/m] ^ (1/BETA)
= 800 * (10) ^ 1/4
= 1422
So with 10 components in the first partition or daisy chain, then Nf @test
(component) = Nf @test (10%) = 1422.
A more conservative analysis neglecting the partition correction would be to say
Nf (10%) = 800.
Which way makes the most sense?
From Nf @test (10%) and BETA, I can calculate Nf @test (50%), then apply the
acceleration factors to get Nf @use (50%), then extrapolate to get Nf @use (1%)
and Nf @use (0.1%).
Best regards,
John Nieznanski
________________________________
This e-mail and any files transmitted with it may be proprietary and are
intended solely for the use of the individual or entity to whom they are
addressed. If you have received this e-mail in error please notify the sender.
Please note that any views or opinions presented in this e-mail are solely those
of the author and do not necessarily represent those of ITT Corporation. The
recipient should check this e-mail and any attachments for the presence of
viruses. ITT accepts no liability for any damage caused by any virus transmitted
by this e-mail.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|