Subject: | |
From: | |
Reply To: | |
Date: | Thu, 9 Oct 2008 10:09:56 -0400 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Just a little caution about simply adopting a recommended pad arrangement
for a component. I have been burned by using a recommended pad size and
location without first laying a part on a 1:1 plot of those pads. You may
want to use their recommended pads as a starting point, but I would strongly
recommend you confirm those pads against an actual part before you "call it
good". You may want to massage those pads based on your process and
experiences. A 1206 component is very common, but remember- not all 1206's
are the same. Just my $.02 Lenny Carter, ERG, Inc. www.ergpower.com
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Donald Kyle
Sent: Thursday, October 09, 2008 9:49 AM
To: [log in to unmask]
Subject: Re: [TN] SMT dimensions guidelines, 1208
You can find land patterns for SMT devices at two places for free.
IPC
http://landpatterns.ipc.org/default.asp
PCB Libraries
http://www.pcblibraries.com/
Donald
At 08:35 AM 10/9/2008, Victor Hernandez wrote:
>Fellow TechNetters:
>
> Where can I find guidelines for chip component - termination pad
>size? What id the nominal copper pad size for a 1206?
>
>Victor.
>
>---------------------------------------------------
>Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
>unsubscribe, send a message to [log in to unmask] with following text in
>the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt
>or (re-start) delivery of Technet send e-mail to
>[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing
>per day of all the posts: send e-mail to
>[log in to unmask]: SET Technet Digest
>Search the archives of previous posts at:
>http://listserv.ipc.org/archives Please visit IPC web site
>http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
>information, or contact Keach Sasamori at [log in to unmask] or
>847-615-7100 ext.2815
>-----------------------------------------------------
Donald Kyle C.I.D.+
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in the
BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet
NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send
e-mail to [log in to unmask]: SET Technet Digest Search the archives of
previous posts at: http://listserv.ipc.org/archives Please visit IPC web
site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|