Hi Graham,

Like Jerry I've never done it but I remember seeing someone solder very
large wire into a very large terminal with a small torch. I don't recall
anything more than that but I might lead you in a direction (kicking and
screaming :-)

KennyB 

-----Original Message-----
From: Jerry Dengler [mailto:[log in to unmask]] 
Sent: Thursday, September 04, 2008 9:49 AM
To: [log in to unmask]
Subject: Re: [TN] Wire Harness question - soldering 0 AWG wire?

Hi Graham,

I've never done this myself but watched it being done at a customers
site.  The had to make a holder for the connector that had a temperature
controlled heater in it.  I believe they used a 50 watt iron.

Regards,

Jerry Dengler
Production Manager
Pergamon Corporation
PH:  610-239-0721
Fax: 610-239-0720
 

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Graham Collins
Sent: Thursday, September 04, 2008 12:35 PM
To: [log in to unmask]
Subject: [TN] Wire Harness question - soldering 0 AWG wire?

Hello TechNet
I've been dragged (kicking and screaming) out of my comfort zone, and am
looking at a wire harness.  I've got some 0 awg wire to solder into a
connector.  We haven't tried it, but I really doubt that my Metcal
MX-500 system is up to this task.  Do any of you have experience with
this, and if so can you recommend equipment or technique?  

regards,
 
Graham Collins
Halifax Production Engineering
(902) 873-2000 ext. 6215


---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------