Leif,
Wow interesting problem.
- 10% defect
- standard finish
- Active water wash solder paste
- new prob on old board
- placement good
- lead free process OK
- lot code specific? Undetermined.
- Try printing paste on bare laminate or glass, placing components and
running at hotter and hotter temperatures to see if there is a
difference. - Perhaps you can just run a slightly hotter leaded
profile.
- Sounds like you are already using a fairly active flux in your solder
paste.
- Running a different make of caps sounds good.
- Any change to that board design where you now have a massive internal
ground plane hooked to one of the tow pads of the caps in question?
Let us know how it turns out.
Bev
RIM
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Leif Erik Laerum
Sent: Tuesday, May 20, 2008 1:05 PM
To: [log in to unmask]
Subject: [TN] 0402 capacitors turning
Technetters,
I am new to this group, but I have scanned the archives and there seems
to a lot of expertise available, so I thought I bring up an issue we are
battling with that I was hoping getting some suggested remedies for.
We have an issue where 0402 Capacitors are turning during reflow. They
are basically clocking beyond the 50% pad coverage rule. We can have as
much as 10% of the caps on one board do this. These are lead free caps
with matte tin termination. The vendor is of course claiming that it is
compatible with eutectic solder and a leaded process. We are using
Sn63Pb37 water soluble solder with an RTS profile.
The boards in question have been built for a while and this is a new
problem. The placement is perfect. The problem does not appear when we
use this same cap on our lead free assemblies.
Within a batch of, say 50 boards, the issue seem to vary with each reel
different. We have not narrowed it down to a specific date code yet, but
that experiment is next. These are all from the same vendor so we are
also planning to try a different vendors capacitors.
One idea I had was that there is some sort of out gassing that move
these caps, but we do not see any blow holes. I am not observing any
other obvious defects and the issue is exclusive to these caps.. The
easy answer is of course to go to a lead free assembly, but that is not
really an option at this point.
Could oxidized caps on the caps cause this. Would using a different
solder with an more aggressive flux be an idea? I have also thought of
reducing the aperture in the stencil to reduce the solder.
Any input would be highly appreciated.
--
Leif Erik Laerum
Quality Assurance Manager
Texas Memory Systems
[log in to unmask]
Tel: (713) 266-3200 x468
www.texmemsys.com
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------------------------
This transmission (including any attachments) may contain confidential information, privileged material (including material protected by the solicitor-client or other applicable privileges), or constitute non-public information. Any use of this information by anyone other than the intended recipient is prohibited. If you have received this transmission in error, please immediately reply to the sender and delete this information from your system. Use, dissemination, distribution, or reproduction of this transmission by unintended recipients is not authorized and may be unlawful.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|