Subject: | |
From: | |
Reply To: | |
Date: | Sun, 23 Mar 2008 16:25:00 -0700 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Your response brings to mind a cartoon which I keep on my desk. It shows two guys, apparently police detectives, standing over a body, discussing the crime. The caption is: "From the multiple of aggressive stab wounds, I would bet the victim was a consultant."
Rudy Sedlak
RD Chemical Company
Lee parker <[log in to unmask]> wrote:
Louis
I would continue the process as you are currently doing. You can never be
too clean or too rich.
Best regards
Lee
J. Lee Parker, Ph.D.
JLP Consultants LLC
804 779 3389
----- Original Message -----
From: "Louis Hart"
To:
Sent: Friday, March 21, 2008 10:20 AM
Subject: [TN] preparation for HASL
TechNetters, a question has come up in our plant about cleaning copper
surfaces before HASL. (Solder used is the standard tin-lead.) We've been
putting panels through a light acid clean and etch, then through a
Quicksilver flux applicator with two rollers that appear to be saturated
with Enthone 757 SG flux. Someone has asked if that acid clean and etch are
really necessary, since what is flux supposed to do?
Any comments on the need for the acid clean and etch would be most welcome.
Many thanks - Louis
Louis Hart
Compunetics
Monroeville, PA
USA
[log in to unmask]
412-858-1272
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------
Looking for last minute shopping deals? Find them fast with Yahoo! Search.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|