Thanks, Brian,
I'll add your advice to my cost calculation, which will go to the
economists in a few minutes.
Will let you know what became of it.
/Inge
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Brian Ellis
Sent: den 8 februari 2008 12:36
To: [log in to unmask]
Subject: Re: [TN] absolutely crazy dispenser question
Four pumps would theoretically be better but, provided your needles had
a reasonable inside diameter, you could probably get away with one. Yes,
low-speed screw pumps would work, but you would probably do better with
the kind that has a chamber filled with paste and a plunger displaces
the paste along the needles (not a piston in a cylinder). The potential
problem with a screw pump is that the paste is subjected to considerable
shear as it is pushed along the rotor, making the chemistry quite
liquid, according to its rheological properties. This can cause metal
particles to come into contact with each other, coalesce and sinter into
clumps which could partially block the needles and then sinter further
onto other particles as they come along. The ideal is to disturb the
paste chemistry as little as possible, ensure a streamline flow along
the pipework, with no abrupt changes of diameter.
Brian
Hernefjord Ingemar wrote:
> You mean four needles in parallel with one and the same pump, or four
> needles with four pumps? Positive displacement, is that same as pumps
> with Archimedes's screws?
> Inge
>
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Brian Ellis
> Sent: den 8 februari 2008 09:59
> To: [log in to unmask]
> Subject: Re: [TN] absolutely crazy dispenser question
>
>
> Syringes, no; needles, yes. I suggest that a positive displacement
> dispenser feeding four needles that can be dragged through your
> assembly would not be difficult to contrive. You would probably need
> about 12 gauge Luer Lock needles, depending on the quantity of paste
> needed and the speed of withdrawal. This would not work well with
> electropneumatic
> dispensers: you must have the positive displacement.
>
> Any medical needle supplier will have something to suit: I used to
> have ad hoc needles made for me by one in Switzerland for
next-to-nothing.
>
> Brian
>
> Hfjord wrote:
>> Hi all,
>>
>> I have 100 mm long tube, quadratic cross section about 15x15 mm. It's
>> made up by 4 pcs double copper sided 'boards' put together to form
>> the
>
>> tube. I need dispense solder paste on INSIDE in all for corners and
>> all along the 100 mm length. Now, have you seen dispenser robotics
>> with syringes that long? I would like to dispense in all four corners
>> simultaneously, but that is probably to be a dream only.
>>
>> No, I can't buy ready to use molded stuff, or other tubular things,
>> nor cut-and-wrap, or any else products. The 4-piece design is given
>> and unchangeable. And..I can't print solder paste on the individuals
>> for later putting together.
>>
>> /Inge
>>
>> ---------------------------------------------------
>> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
>> unsubscribe, send a message to [log in to unmask] with following text
>> in
>
>> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt
>> or (re-start) delivery of Technet send e-mail to [log in to unmask]:
>> SET
>
>> Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
>> posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
>> archives of previous posts at: http://listserv.ipc.org/archives
>> Please
>
>> visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
>> for additional information, or contact Keach Sasamori at
>> [log in to unmask] or 847-615-7100 ext.2815
>> -----------------------------------------------------
>>
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
> unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt
> or
> (re-start) delivery of Technet send e-mail to [log in to unmask]: SET
> Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
> posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
> archives of previous posts at: http://listserv.ipc.org/archives Please
> visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
> for additional information, or contact Keach Sasamori at
> [log in to unmask] or 847-615-7100 ext.2815
> -----------------------------------------------------
>
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
> unsubscribe, send a message to [log in to unmask] with following text in
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt
> or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET
> Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
> posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
> archives of previous posts at: http://listserv.ipc.org/archives Please
> visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
> for additional information, or contact Keach Sasamori at
> [log in to unmask] or 847-615-7100 ext.2815
> -----------------------------------------------------
>
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
