TECHNET Archives

October 2007

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
"Stadem, Richard D." <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, Stadem, Richard D.
Date:
Wed, 24 Oct 2007 12:37:34 -0500
Content-Type:
text/plain
Parts/Attachments:
text/plain (60 lines)
This type of rework should only be performed using either a hand-held
hot air gun (Hakko) or use the hot gas rework station, and should only
be done by a skilled operator. If the hot gas rework station is used, it
is not usually necessary to include a board pre-heat stage, just a
ramp-up to preheat the area from the top only using a small nozzle to
direct the air flow in the immediate vicinity of the capacitor and then
quickly lift it off. This can easily be accomplished without allowing
the PWB temperature to go above 125C. MLCCC capacitors should use the
same processes.

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Chafin, Ken G.
Sent: Wednesday, October 24, 2007 10:22 AM
To: [log in to unmask]
Subject: [TN] Surface Mount Tantalum Capacitor Repair and Rework--Risks
Involved

I would be interested in receiving any literature on the above subject.
Approx. 8--9 years ago we encountered many failures because  we
outsourced some surface mount boards and the supplier did a lot of
repair and replacement of SMT tantalum capacitors using soldering irons.

Both Kemet and Vishay Sprague were helpful by providing Engineering
Bulletins on the risks involved in the hand soldering of SMT tantalum
Caps.
We are again contemplating outsourcing this type of rework.  We really
need to know the risks involved in doing this and how best to do the
rework if it must be done.

Any documents (or personal experience) you think might help with this
decision would be appreciated--- [log in to unmask]

Thanks

Kenneth Chafin


---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2