TECHNET Archives

October 2007

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
Barry Gallegos <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, Barry Gallegos <[log in to unmask]>
Date:
Thu, 11 Oct 2007 13:37:41 -0600
Content-Type:
text/plain
Parts/Attachments:
text/plain (100 lines)
Richard,
Many thanks. I did not know that. I will pass this on to my group.

Barry.



-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard D.
Sent: Thursday, October 11, 2007 1:35 PM
To: [log in to unmask]
Subject: Re: [TN] Shielding for BGA rework

Finally, something I know a little bit about.
I have learned that Kapton tape should never be used as a masking tape
on circuit boards for rework, or for any other purpose either. What I
did not know is that Kapton (polyamide) tape generates a gigantic ESD
charge (greater than 5kv) when pulled off of the reel, and about 500v
when pulled off of the circuit board. This was shown to me by an ESD
engineer.
I also know that polyamide tape is an excellent heat conductor (not
insulator) and does not work very well as a maskant to form a barrier to
protect adjacent or surrounding components when performing hot gas
rework. It does work well to hold a thermocouple to the board, and the
actual temperature drop through the polyamide tape is exactly 1 degree
C., so it is OK to use for that, but only on a bare PWB or a scrap
board. After the display by the ESD consultant, I now cringe when I go
into factories and see the polyamide tape on workbenches. I know there
are dispensers that supposedly remove the charge, but how about when the
tape is removed from the board?

There are masking tapes made just for shielding of other components when
doing rework. They look just like the masking tape you use when
painting, except they are high-temperature tape and are dissipative. Two
companies that make them are Intertape Corp. and 3M. Intertape's p.n. is
T-33-1 PRT054. I do not have the 3M tape part number, but I am sure your
local 3m rep would be glad to take you out to lunch and give you that
info and a whole bunch more. These tapes do have a higher adhesive
content and can leave some residue on the components, but an alcohol
brushing cleans it off completely.
   

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Genny Gibbard
Sent: Thursday, October 11, 2007 2:06 PM
To: [log in to unmask]
Subject: [TN] Shielding for BGA rework

Hello again,
Does anyone use any shielding for adjacent components and PCB material
when they are reworking a BGA, in order to minimize the heat seen by
those areas in close proximity?

If so, what do you use?  Is there a commercially available product, or
do you just make your own as needed (someone here said they had seen
foil and kapton tape used elsewhere).

Thanks much, as always.
Genny.

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2