Amol,
First of all, I want to preface this by saying that I am aware that this
is not a forum for brand or product advertisement, and I am not trying
to do that, and I apologize in advance if this is construed as such
because that is not the intent.
I do realize however that this can be quite a problem and I felt that it
would be a disservice to you and the forum if I did not mention a
possible solution.
Please view this link and feel free to contact me offline if this
solution is of interest to you.
http://www.pentagon-ems.com/spotlight/archives/050806/spotlight_050806.h
tml
I hope you find a solution that works for you.
Good luck,
Randy Morrison
Marketing Manager
Pentagon EMS
http://www.pentagon-ems.com/bio/randy.html
[log in to unmask]
Tel: 503-924-2747 Ext. 222
Fax: 503-924-2744
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Kane, Amol (349)
Sent: Thursday, August 16, 2007 8:46 AM
To: [log in to unmask]
Subject: [TN] Press Fit Connector rework
Dear Technetters,
Is anybody aware of ways to remove press fit connectors once they are
inserted in the PTHs??. We have a situation where the connector is
removing plating from the PTHs as well as removing the annular ring on
the outside of the holes. The surface finish is ENIG. So far the
investigation has revealed that the hole size and the pin size is within
tolerance. While we are determining the root cause, we also need to see
if there is a way to rework these boards.
I have some pictures which I can post if anyone wants to take a look.
Thanks in advance,
Amol
CONFIDENTIALITY NOTICE:
This e-mail, and any attachments, is for the sole use of the intended
recipient(s) and may contain information that is confidential and
protected from disclosure under the law. Any unauthorized review, use,
disclosure, or distribution is prohibited. If you are not the intended
recipient, please contact the sender by reply e-mail, and delete/destroy
all copies of the original message and attachments.
Thank you.
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
