Steve,
would you mind to post them on Steve Gregory's webpage? (Steven..would you?)
i would also like to have a lok at them.
thanks in advance, Ivan
>Steve,
>That would be useful. Yes, please send.
>Bev
>
>-----Original Message-----
>From: Steve Kelly [mailto:[log in to unmask]]
>Sent: Monday, July 16, 2007 12:17 PM
>To: 'TechNet E-Mail Forum'; Bev Christian
>Subject: RE: [TN] Question about rework of paste in hole solder joints
>
>Hi Bev, I can send you some pictures of some parts without what I would call IPC
>standard hole fill that are used in a very rugged military environment
>and
>the customer has had no issues. They put these through heavy vibration,
>thermal etc. with no issues but in all cases they had at least some
>fill.
>Regards Steve Kelly
>
>-----Original Message-----
>From: TechNet [mailto:[log in to unmask]] On Behalf Of Bev Christian
>Sent: July-16-07 11:44 AM
>To: [log in to unmask]
>Subject: [TN] Question about rework of paste in hole solder joints
>
>Technetters, Good morning! We generally do not use PTH parts. As a result, we
>do
>not do wave soldering, but use paste-in-hole or pin-in-paste, chose your
>moniker. Because we buy the part in question from two different
>suppliers, who make the parts with different dimensions, we have had to
>use fairly large, oval holes instead of a more conventional round hole.
>And the part leads do not stick out the bottom of the hole either. With
>overprinting we have been able to get what is deemed adequate solder
>joint strength (and reliability (Yes, I know the difference, Werner.)),
>even though the hole fill is not stellar. Wetting angles are good and
>proper intermetallics are formed.
>
>Now let's say we do a rework - removing the component, dressing the hole,
>inserting a new part and resoldering using hand soldering with
>cored wire. The internal debate is whether we should demand hole fill
>to meet normal IPC standards or whether we allow the same amount of hole
>fill that is allowed for the original paste-in-hole. Opinions and/or
>experiences (if you are willing to share the latter :) ) appreciated.
>Thanks in advance.
>
>Bev
>RIM
>
>--------------------------------------------------------------------- This
>transmission (including any attachments) may contain confidential
>information, privileged material (including material protected by the
>solicitor-client or other applicable privileges), or constitute
>non-public
>information. Any use of this information by anyone other than the
>intended
>recipient is prohibited. If you have received this transmission in
>error,
>please immediately reply to the sender and delete this information from
>your
>system. Use, dissemination, distribution, or reproduction of this
>transmission by unintended recipients is not authorized and may be
>unlawful.
>
>---------------------------------------------------
>Technet Mail List provided as a service by IPC using LISTSERV 15.0
>To unsubscribe, send a message to [log in to unmask] with following text
>in
>the BODY (NOT the subject field): SIGNOFF Technet
>To temporarily halt or (re-start) delivery of Technet send e-mail to
>[log in to unmask]: SET Technet NOMAIL or (MAIL)
>To receive ONE mailing per day of all the posts: send e-mail to
>[log in to unmask]: SET Technet Digest
>Search the archives of previous posts at:
>http://listserv.ipc.org/archives
>Please visit IPC web site
>http://www.ipc.org/contentpage.asp?Pageid=4.3.16
>for additional information, or contact Keach Sasamori at [log in to unmask]
>or
>847-615-7100 ext.2815
>-----------------------------------------------------
>
>--------------------------------------------------------------------- This
>transmission (including any attachments) may contain confidential information,
>privileged material (including material protected by the solicitor-client or
>other applicable privileges), or constitute non-public information. Any use of
>this information by anyone other than the intended recipient is prohibited. If
>you have received this transmission in error, please immediately reply to the
>sender and delete this information from your system. Use, dissemination,
>distribution, or reproduction of this transmission by unintended recipients is
>not authorized and may be unlawful.
>
>--------------------------------------------------- Technet Mail List provided
>as a service by IPC using LISTSERV 15.0
>To unsubscribe, send a message to [log in to unmask] with following text in
>the BODY (NOT the subject field): SIGNOFF Technet
>To temporarily halt or (re-start) delivery of Technet send e-mail to
>[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of
>all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
>archives of previous posts at: http://listserv.ipc.org/archives
>Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
>additional information, or contact Keach Sasamori at [log in to unmask] or
>847-615-7100 ext.2815 -----------------------------------------------------
>
>
----------------------------------------------------------------------------
DEXGATEMICRO il centralino VoIP multifunzione per l'azienda.
Prova gratuita per 30 giorni e 4 utenti!
Scopri tutte le funzionalita' sul sito Dexgatemicro.com
----------------------------------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|