The edge of Dewey's humor will be forever sharp

John

 
 
John Burke
 
(408) 515 4992
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Whittaker, Dewey (EHCOE)
Sent: Tuesday, July 10, 2007 6:48 AM
To: [log in to unmask]
Subject: Re: [TN] Injury by array

One must be very careful when working with cutting edge technology.
Dewey

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of McGlaughlin, Jeffrey
A
Sent: Tuesday, July 10, 2007 4:23 AM
To: [log in to unmask]
Subject: [TN] Injury by array

Oh wise and wonderful members of tech net -

We have had to incidents in the past six months where assemblers have
been cut while handling assembly arrays (2-up panels) for one of our
products. This has elevated the issue to "Panic Mode" due to the
involvement of EHS&Q (environmental health, safety and quality). As the
designer of the array I have been given ownership of the issue and am
task with resolving it.  After 20+years of handling boards and arrays I
have never been cut, so I am unsure as to what if any corrective action
can be taken to prevent future injuries.

The specifics on the arrays -
10.5" [267mm] x 12.0" [305mm] x 0.062" [1.6mm] thick
2 - up for 4.7"[119.3mm] x 9.2" [233.6mm] PCB
Minimum rail 0.38"[9.5mm]
Tab Route and Retain (mouse bite)
Injuries occurred during loading of the solder printer and during slide
line operations for post reflow assembly. 

Any suggestions on what to tell our production group?

Jeffrey McGlaughlin, CID 
Engineering Designer 
Battelle 
505 King Avenue 
Columbus Ohio 43201-2693 
(614)424-7582 Phone 
(614)458-7582 Fax 
PS Don't you just love all those  management buzzwords (underlined.)
>;-D 

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------