You all have been a big help. I'm going to ask manufacturing for more information. I have a feeling this is just a matter of opinion. I've used the 2221 table 9-3 recommendation and then some. Maybe they just had some bad experiences in the past that I'm not aware of.
Allen Maddox, CID+
"Wolfe, Robert" <[log in to unmask]> wrote:
Jeff,
Yes we have seen that too on a single side,
also with insertion machines, the lead can catch
and rip up the pad up too.
But if the pad is reasonable in size to hole,
it should limit the problem, (except for the gorillas)
they always pose a problem.
Bob
-----Original Message-----
From: DesignerCouncil [mailto:[log in to unmask]] On Behalf Of Jeff
Seeger
Sent: Tuesday, June 05, 2007 11:19 AM
To: [log in to unmask]
Subject: Re: [DC] Concerns about Single Sided Board
I'm going waaaay back here but it sounds to me like there
may be an issue with the size of the great apes on the factory
floor. I recall having many problems on a paper-epoxy
single sided board where handling post assembly and before
test was causing components to be pushed through and so
lifting the land, track, solder joint and everything. These
were not small pads, either.
One cure for that was simply plating the hole, while not the
most graceful solution the added adhesion vastly reduced the
frequency and severity of damage. What I can't recall is if
we tried simply switching to FR4.
Yikes, I'm dating myself... Just guessing someone else in that
decision chain is my age...
--
Jeff Seeger Applied CAD Knowledge Inc
Chief Technical Officer Tyngsboro, MA 01879
jseeger "at" appliedcad "dot" com 978 649 9800
------------------------------------------------------------------------
---------
DesignerCouncil Mail List provided as a free service by IPC using
LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET
DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases
> E-mail Archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
------------------------------------------------------------------------
---------
DISCLAIMER:
Important Notice *************************************************
This e-mail may contain information that is confidential, privileged or otherwise protected from disclosure. If you are not an intended recipient of this e-mail, do not duplicate or redistribute it by any means. Please delete it and any attachments and notify the sender that you have received it in error. Unintended recipients are prohibited from taking action on the basis of information in this e-mail.E-mail messages may contain computer viruses or other defects, may not be accurately replicated on other systems, or may be intercepted, deleted or interfered with without the knowledge of the sender or the intended recipient. If you are not comfortable with the risks associated with e-mail messages, you may decide not to use e-mail to communicate with IPC. IPC reserves the right, to the extent and under circumstances permitted by applicable law, to retain, monitor and intercept e-mail messages to and from its systems.
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
---------------------------------------------------------------------------------
DesignerCouncil Mail List provided as a free service by IPC using LISTSERV 1.8d
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF DesignerCouncil.
To temporarily stop/(restart) delivery of DesignerCouncil send: SET DesignerCouncil NOMAIL/(MAIL)
Search previous postings at: www.ipc.org > On-Line Resources & Databases > E-mail Archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
---------------------------------------------------------------------------------
|