TECHNET Archives

May 2007

TechNet@IPC.ORG

Options: Use Monospaced Font
Show Text Part by Default
Show All Mail Headers

Message: [<< First] [< Prev] [Next >] [Last >>]
Topic: [<< First] [< Prev] [Next >] [Last >>]
Author: [<< First] [< Prev] [Next >] [Last >>]

Print Reply
Subject:
From:
"Dehoyos, Ramon" <[log in to unmask]>
Reply To:
TechNet E-Mail Forum <[log in to unmask]>, Dehoyos, Ramon
Date:
Wed, 9 May 2007 11:00:06 -0400
Content-Type:
text/plain
Parts/Attachments:
text/plain (635 lines)
	Prior to Lead Free, the world wide use of HASL was 60% and FTL was 3%. Now the HASL use probably is down.
	Ramon
	 

-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Brian Ellis
Sent: Wednesday, May 09, 2007 4:15 AM
To: [log in to unmask]
Subject: Re: [TN] (2) What is the difference between Fused SnPb and HASL?

Mike

I agree that there is some distortion of facts in the previous post. It may be true that in/lead plating may have minor variations of thickness if the plating operation is not well controlled. A couple of former lives ago, I made boards with FTL and the throwing power was such that the thickness in the PTHs was about 10% less in the centre of the hole
(1.6 mm laminate). After fusion, the barrel was evenly tinned until it started to thin down at the corners. On the pads, the uniformity of the coating was much better than with HASL, and the thickness of the tinning on the corners was typically about 2 µm as opposed to <1 µm for HASL, and there was never any of the beading that HASL gives. I did the fusion in a stabilised polypropylene glycol ether blend: a dirty process but, oh, so good in its performance.

Brian

Barmuta, Michael wrote:
> Hi Richard: I have to take issue with some of your comments. 
> First of all I'm not a proponent of HASL. Secondly, I built fused 
> tin/lead (FTL) boards for over twenty five years so I probably know a 
> little bit about it.
> 
> 
> 	
> Regards
> 	
> Michael Barmuta
> 	
> Staff Engineer
> 	
> Fluke Corp.
> 	
> Everett WA
> 	
> 425-446-6076
> 
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard D.
> Sent: Tuesday, May 08, 2007 1:25 PM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> And in rebuttal, also because fused tin/lead allows a very flat 
> surface without some of the drawbacks of immersion silver, ENIG, OSP, 
> and of course, HASL. A FTL surface is not flat. It suffers from uneven 
> thickness.
> This is caused by variations in current density during the 
> electroplating of the tin/lead.
> High current density areas have more plating than the LCD areas. Thus 
> they end up with thicker deposits
> 
> There are a lot of companies using FTL finish on PWBs, and for very, 
> very good reasons. Although it may cost slightly is a pretty non 
> descript term.
> I have found if you want FTL without the TL under the mask i.e. with 
> the additional selective masking and stripping it is a 20% adder.
> IF you can find someone to do it.
> more than HASL, its
> application process is much easier on the PWB than HASL, and it can 
> effectively be applied the first time without a bunch of rework, The 
> reason there is not a bunch of rework on a FTL board is you cant 
> rework one, once it's been etched.
> It can't be re-plated and if it didn't wet to the surface copper 
> during fusing there's nothing you can do to fix it.
> which is not always true of HASL.
> As illustrated in all of these postings, FTL is a very misunderstood 
> plating. Properly applied, it does NOT leave tin/lead under the 
> soldermask. The standard FTL process DOES leave TL on the circuitry 
> unless you go thru a process intensive set of masking, stripping and 
> cleaning steps.
> It does NOT leave copper slivers along the tops of features.
> It does NOT present a surface that is difficult for soldermask to 
> adhere to. "Why not just build a SMOBC/HASL board?" There are a lot of reasons.
> 
> First of all, I have yet to see a board house that can consistently, 
> over time, provide HASL boards where the HASL was not reworked at 
> least one time before the boards ever leave the fabricator, and 
> usually it is done many times. If your board supplier has to run back 
> thru HASL many times you've got the wrong board supplier.
> Evidence of this is manifest in the number of postings on this forum 
> where HASL PWBs were received that could not be soldered properly due 
> to dewetting issues. This is because after a certain number of HASL 
> rework cycles there is so much Cu diffused into the HASL that during 
> the initial soldering processes there is already a high level of 
> dewetting taking place.
> 
> Secondly, the HASL deposits are extremely non-uniform, As are certain 
> FTL designs. See above on current density.
> with some areas/pads retaining much more of the HASL solder than 
> others, and very poor gasketing between the stencil and the board 
> occurs. This is the reason other plating methods were looked at as 
> components developed finer pitches, along with the advent of the BGA. 
> Trying to place a component with thin compliant leads less than .020" 
> apart or round balls on top of a pad covered with a single dome of 
> hard solder and covered with thousands of tiny little solder marbles 
> (paste) just does not work very well. It usually leads to bridging and 
> non-uniform paste deposits in both volume and shape on all but the 
> most basic, 50mil-pitch PWBs.
> Thus the development of ENIG, IAg, OSP, etc., which are all flat 
> finishes. I don't think you'll see much wide spread use of FTL in 
> commercial, industrial,  telecommunications, etc. but som how they get 
> it done.
> 
> FTL is still commonly used, especially in military, avionics, and 
> space programs, by quite a few companies. I would question about it 
> being commonly used.
> If it was widely used you would find a lot more shops offering it. I 
> don't have the number but I would guess it is very small percentage of 
> all boards fabricated world wide.
> Like any other finish, your successwith it is directly dependent on 
> the  performance of the board fabricator who applies it. Properly 
> done, it can be one of the best, most reliable finishes you can 
> possibly solder to. And just like you said, Ramon, it works.
> Yes but at a definite $cost penalty that's why you see it still being 
> used in military, avionics and space.
> They don't care what  the price is and are still running on 30 year 
> old drawing and call outs.
> 
> FTL provides excellent solderability, without all of the harshness and 
> variability and stresses to the PWB present with HASL.
> FTL has it's own issues on harshness, variability and stresses. 
> The boards are normally run thru a heat cycle such as an IR oven to 
> melt the co-deposited electroplated TL. Ask someone from the military
> 
> how they like their high frequency Teflon multilayer board run thru 
> the fuser.
> That's why they use not melting final finishes
> 
> I am not saying HASL has no place, either. There are different 
> finishes, all have their strengths and drawbacks. HASL is simply not 
> my first choice as a surface finish when I am determining what to use 
> for the guidance system of a nuclear missile, a flight control 
> computer, an airport tower communications system, or a traffic control 
> system for a high-speed train, for example. I would certainly feel 
> comfortable designating FTL if the design warranted it, however.
> 
> Selective FTL has its place if you really need it and want to pay for 
> it
> 
> but I see it as a dying technology that will have limited availability. 
> A dinosaur of the past, living on due to ghosts walking the hall.
> 
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Dehoyos, Ramon
> Sent: Tuesday, May 08, 2007 1:47 PM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> 	Hi Michael: HASL is much less expensive and less time consuming to 
> plate. Selective solder reflow is used by very few companies that are 
> not ready to change the way things were made long time ago just 
> because it works.
> 	Regards,
> 	Ramon
> 
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Barmuta, Michael
> Sent: Tuesday, May 08, 2007 11:37 AM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> Hi Ramon: As I said "conventionally built" fused Sn/PB boards have the 
> fused Sn/Pb on the circuitry under the mask. This is how standard 
> fused Sn/Pb board were built in the 60's, 70's and beyond. A more 
> unconventional approach is what you are referring to. Boards can be 
> built this way but are more complicated and expensive due to the 
> additional processing. However it will take care of the melting metals 
> under the mask condition.
> 
> If you are going to go to all the trouble of maintaining a Sn/Pb 
> plating line, plating Sn/Pb, selectively masking, selectively 
> stripping the plating, stripping the masking, fusing,  washing, 
> cleaning the exposed Cu,  applying soldermask, etc, why not just build a SMOBC/HASL board.
> It's much simpler.
> 
> 	
> Regards
> 	
> Michael Barmuta
> 	
> Staff Engineer
> 	
> Fluke Corp.
> 	
> Everett WA
> 	
> 425-446-6076
> 
> 	
> 
>  
> -----Original Message-----
> From: Dehoyos, Ramon [mailto:[log in to unmask]]
> Sent: Tuesday, May 08, 2007 7:37 AM
> To: TechNet E-Mail Forum; Barmuta, Michael
> Subject: RE: [TN] What is the difference between Fused SnPb and HASL?
> 
> 
> 
> 	Michael:
> 	        Traces or other geometries that are not to be soldered and 
> are going to be under the solder mask do not need to have fused solder 
> at all, just pure cleaned, bright copper. If solder is left over the 
> traces that are under the solder mask, it will melt when board is 
> reflowed or wave soldered as you said. That would not be a good thing.
> Solder mask should adhere to the copper well and not be affected by 
> process temps much at all.
> 	Regards,	
> 	Ramon
> 
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Barmuta, Michael
> Sent: Tuesday, May 08, 2007 10:21 AM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> Wee: A fused Sn/Pb board is normally covered by soldermask. If not you 
> could obviously have a real mess at wavesolder.
>  
> The problem with a conventionally built fused Sn/Pb board i.e. 
> circuitry is fused Sn/Pb, is that during reflow and/or wavesolder the 
> Sn/Pb melts under the mask. This can cause adhesion failure of the 
> soldermask to the Sn/Pb. It is especially true for larger features, 
> ground planes, etc. If the board is then washed the condition can be 
> aggravated by the chemistry and spray impingement resulting in 
> additional loss mask or entrapment of wash residues.
> 
> This was one of the drivers for going to a SMOBC style of 
> construction, no melting metal under the mask.
> 
> 									
> 	
> Regards
> 	
> Michael Barmuta
> 	
> Staff Engineer
> 	
> Fluke Corp.
> 	
> Everett WA
> 	
> 425-446-6076
> 
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Lum Wee Mei
> Sent: Monday, May 07, 2007 5:37 PM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> Thanks for the responds. From what I have gathered, fused SnPb can 
> also have solder mask on them. My initial understanding or 
> interpretation was that HASL finish is for SMOBC while fused SnPb 
> finish is for board without solder mask.
>  
> Regards,
> Wee Mei
> 
> ________________________________
> 
> From: TechNet on behalf of Dehoyos, Ramon
> Sent: Mon 5/7/2007 10:15 PM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> 
> 
>         Wayne:
>         Mostly copper with SnPb over it on some slivers. Pure copper 
> from geometries such as traces and with SnPb such as pads. The slivers 
> can be very small or very large. It depends on how it was removed. 
> Large by hand and small by pumice spray. If they break off and wash 
> away, no problem. If they partially break off and stay, they may 
> shorten geometries. Other name for them is inclusions.
>      Ramon
> 
>            >>>>> --------------- <<<<<  The edges at the top will 
> break off as slivers.
>                       |           |
>                    |         |
>                     |       |
>                      |     |
>                      -------
>                
> 
> 
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Wayne Thayer
> Sent: Monday, May 07, 2007 9:53 AM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> Ramon-
> 
> But it was the SnPb which had slivers, and if that is chemically 
> etched away, then what are the slivers made from?
> 
> Wayne
> 
>>>> [log in to unmask] 5/7/2007 9:16 am >>>
> Wayne:
>         That is affirmative. SnPb is removed from everywhere except 
> the pads, lands and anything else that needs solder over the top of copper.
> At this time bare copper is oxidized and needs to be cleaned by hand 
> or spray so that SMOBC can adhere to it and slivers brake off.
>         Ramon
>         
> 
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Wayne Thayer
> Sent: Monday, May 07, 2007 8:56 AM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> Ramon-
> 
> What is it that needs mechanical removal?  The oxidation of the copper 
> traces due to selective SnPb removal?
> 
> Wayne
> 
>>>> [log in to unmask] 5/7/2007 8:46 am >>>
> 
> 
>         Fused solder is more expensive and it takes about 5 more steps.
> When the SnPb is used as etch resist, as Wayne mentions, to pattern 
> the outer layers and plate the pads and lands, the etching is not 
> vertical so there is some underetching.
> slivers are formed at the top edge of the geometries.  Later the 
> traces have the SnPb taken off.  So prior to having the solder mask 
> applied, the copper traces are dull due to oxidation from etching the 
> SnPb off which needs to be mechanically removed, leaving possible 
> inclusions partially broken off. It can be a messy situation. Pads and 
> lands are left with the solder over them which is later on fused by reflow oven.
> Thus the name fused solder. Most companies use HASL very few use Fused 
> solder.
>         Ramon
> 
> 
> 
> -----Original Message-----
> From: TechNet [mailto:[log in to unmask]] On Behalf Of Wayne Thayer
> Sent: Monday, May 07, 2007 8:14 AM
> To: [log in to unmask]
> Subject: Re: [TN] What is the difference between Fused SnPb and HASL?
> 
> Werner is quite correct but only mentioned the metallurgy, not the 
> ramifications for processing.
> 
> HASL is a quite obnoxious process in terms of board stress during 
> application, but most non-aggressive board constructs can handle it:
> The panel is plunged into a vat of molten solder and then withdrawn 
> while being blown off with very hot air.  The deposits are lumpy, and 
> start giving problems for smaller parts.
> 
> Fused SnPb is just convection heated to slightly above the melting 
> point--no thermal shock.  Also the deposits are extremely even, so 
> very fine pitch work is no problem.  However, the normal way of 
> achieving Fused SnPb is to use the plated SnPb for the final etch 
> resist.  This means that if you have a board with a solder mask, then 
> the SnPb will be under the mask, which will greatly reduce its effectiveness.
> 
> Wayne Thayer
> 
>>>> [log in to unmask] 5/6/2007 9:39 pm >>>
> Hello,
> 
> I come across QML vendors that state their finish system : HASL, Fused 
> Solder, while some only states : HASL. I know that HASL stands for 
> "Hot Air Solder Leveling", what then is fused solder? There must be 
> some difference between them - what are they?
> 
> Thanks and regards,
> Wee Mei
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing 
> per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional 
> information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100
> ext.2815
> -----------------------------------------------------
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to [log in to unmask]: SET 
> Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
> posts: send e-mail to [log in to unmask]: SET Technet Digest Search the 
> archives of previous posts at: http://listserv.ipc.org/archives Please 
> visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
> for
> additional information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100 ext.2815
> -----------------------------------------------------
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing 
> per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional 
> information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100
> ext.2815
> -----------------------------------------------------
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing 
> per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional 
> information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100
> ext.2815
> -----------------------------------------------------
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing 
> per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional 
> information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100
> ext.2815
> -----------------------------------------------------
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to [log in to unmask]: SET 
> Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
> posts: send e-mail to [log in to unmask]: SET Technet Digest Search the 
> archives of previous posts at: http://listserv.ipc.org/archives Please 
> visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 
> for additional information, or contact Keach Sasamori at 
> [log in to unmask] or 847-615-7100 ext.2815
> -----------------------------------------------------
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing 
> per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional 
> information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100
> ext.2815
> -----------------------------------------------------
> 
> 
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing 
> per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional 
> information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100
> ext.2815
> -----------------------------------------------------
> 
> This message (including any attachments) contains confidential and/or 
> proprietary information intended only for the addressee.
> Any unauthorized disclosure, copying, distribution or reliance on the 
> contents of this information is strictly prohibited and may constitute 
> a violation of law.  If you are not the intended recipient, please 
> notify the sender immediately by responding to this e-mail, and delete 
> the message from your system.  If you have any questions about this 
> e-mail please notify the sender immediately.
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to [log in to unmask]: SET 
> Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
> posts: send e-mail to [log in to unmask]: SET Technet Digest Search the 
> archives of previous posts at: http://listserv.ipc.org/archives Please 
> visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 
> for additional information, or contact Keach Sasamori at 
> [log in to unmask] or 847-615-7100 ext.2815
> -----------------------------------------------------
> 
> 
> This message (including any attachments) contains confidential and/or 
> proprietary information intended only for the addressee.
> Any unauthorized disclosure, copying, distribution or reliance on the 
> contents of this information is strictly prohibited and may constitute 
> a violation of law.  If you are not the intended recipient, please 
> notify the sender immediately by responding to this e-mail, and delete 
> the message from your system.  If you have any questions about this 
> e-mail please notify the sender immediately.
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing 
> per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional 
> information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100
> ext.2815
> -----------------------------------------------------
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or
> (re-start) delivery of Technet send e-mail to [log in to unmask]: SET 
> Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
> posts: send e-mail to [log in to unmask]: SET Technet Digest Search the 
> archives of previous posts at: http://listserv.ipc.org/archives Please 
> visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 
> for additional information, or contact Keach Sasamori at 
> [log in to unmask] or 847-615-7100 ext.2815
> -----------------------------------------------------
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or (re-start) delivery of Technet send e-mail to
> [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing 
> per day of all the posts: send e-mail to
> [log in to unmask]: SET Technet Digest
> Search the archives of previous posts at:
> http://listserv.ipc.org/archives
> Please visit IPC web site
> http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional 
> information, or contact Keach Sasamori at [log in to unmask] or 
> 847-615-7100
> ext.2815
> -----------------------------------------------------
> 
> 
> This message (including any attachments) contains confidential and/or 
> proprietary information intended only for the addressee.
> Any unauthorized disclosure, copying, distribution or reliance on the 
> contents of this information is strictly prohibited and may constitute 
> a violation of law.  If you are not the intended recipient, please 
> notify the sender immediately by responding to this e-mail, and delete 
> the message from your system.  If you have any questions about this 
> e-mail please notify the sender immediately.
> 
> ---------------------------------------------------
> Technet Mail List provided as a service by IPC using LISTSERV 15.0 To 
> unsubscribe, send a message to [log in to unmask] with following text in 
> the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt 
> or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET 
> Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the 
> posts: send e-mail to [log in to unmask]: SET Technet Digest Search the 
> archives of previous posts at: http://listserv.ipc.org/archives Please 
> visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 
> for additional information, or contact Keach Sasamori at 
> [log in to unmask] or 847-615-7100 ext.2815
> -----------------------------------------------------
> 

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To unsubscribe, send a message to [log in to unmask] with following text in the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest Search the archives of previous posts at: http://listserv.ipc.org/archives Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------

ATOM RSS1 RSS2