Subject: | |
From: | |
Reply To: | |
Date: | Fri, 18 May 2007 09:11:12 -0400 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Or the land could be cut with an exacto knife and the unneeded
part of the land is removed by peeling it off using tweezers and a heat
gun. Land (SMT) Pad (THT).
Ramon
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Stadem, Richard D.
Sent: Thursday, May 17, 2007 11:19 AM
To: [log in to unmask]
Subject: Re: [TN] MELF Experiment
If you have not had too much coffee, using a scrap board, you can take a
high speed dental drill with a very small ball mill and under a
microscope mill away the periphery of the existing pads to the shape you
wish. I have done this many times in the past, it is not that hard to
do. If you bite into the PWB or masking a little bit, it does not hurt
anything.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Black, Paul
Sent: Thursday, May 17, 2007 9:28 AM
To: [log in to unmask]
Subject: [TN] MELF Experiment
Hi Everyone,
A little while ago, I asked for advise regarding a tombstoning issue
with a MELF. I received some replies and they all indicated that the
pads are probably too large. Now, I would like to run an experiment to
prove that out before changing the artwork on the board. I asked my
board fabricator if they could rework some boards by adding soldermask
to half the pad but I was told that the mask wouldn't adhere over the
Immersion Silver finish on the pad. Does anyone have a suggestion that I
could try?
Thank you,
Paul Black
Manufacturing Engineer
Kronos Incorporated
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0 To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|