Subject: | |
From: | |
Reply To: | |
Date: | Thu, 26 Apr 2007 17:30:23 -0400 |
Content-Type: | text/plain |
Parts/Attachments: |
|
|
Vias in the formal sense of the word -- not just thru-holes...
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Dwight Mattix
Sent: Thursday, April 26, 2007 5:24 PM
To: [log in to unmask]
Subject: Re: [TN] "plated shut vias"
At 12:23 PM 4/26/2007, Werner Engelmaier wrote:
>Hi All,
>Vias should never be specified in terms of finished hole size (there is
no
>functional need for any specific finished hole diameter),
And yes I agree wholeheartedly that the drilled diameter is the most
critical dimension -- especially in the case of pressfit connectors
where a
gas tight joint w/out over stressing the barrel/post is the goal.
However, in the case of pressfit connectors, I beg to differ about
finished
hole diameter not being needed . Min hole size is very important in
this
case. It determines the point at which insert forces get too high and
bad
things start to happen (e.g. "Z-ing" in pins to board surface).
dw
> but in terms of
>drilled hile diameter, because that determines all kinds of things
>important to
>the reliability of the via interconnect structure.
>
>Werner
>
>
>
>**************************************
> See what's free at http://www.aol.com.
>
>---------------------------------------------------
>Technet Mail List provided as a service by IPC using LISTSERV 15.0
>To unsubscribe, send a message to [log in to unmask] with following text
in
>the BODY (NOT the subject field): SIGNOFF Technet
>To temporarily halt or (re-start) delivery of Technet send e-mail to
>[log in to unmask]: SET Technet NOMAIL or (MAIL)
>To receive ONE mailing per day of all the posts: send e-mail to
>[log in to unmask]: SET Technet Digest
>Search the archives of previous posts at:
http://listserv.ipc.org/archives
>Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
>for additional information, or contact Keach Sasamori at [log in to unmask]
or
>847-615-7100 ext.2815
>-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text
in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives
Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional
information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100
ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 15.0
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
|
|