Tooling Holes? Never mind, TGIF.
Regards,
Steve Smith
Product Engineer
Staco Energy Products Co.
Web Site: www.stacoenergy.com
& www.stacopower.com
DISCLAIMER AND/OR CONFIDENTIALITY NOTICE:
This message, including any attached materials, is intended solely for
the use of the individual or entity to whom it is addressed and may
contain information that is privileged, confidential, and exempt from
disclosure under applicable law. If the reader of this electronic mail
transmission is not the intended recipient, you are hereby notified that
any dissemination, distribution, or copying of this communication is
strictly prohibited. If you have received this communication in error,
please e-mail or call Staco Energy Products Co. at (937) 253-1191. Thank
you for your cooperation.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Steve Smith
Sent: Friday, February 02, 2007 11:12 AM
To: [log in to unmask]
Subject: [SPAM] Re: [TN] Tooling Hole Quantity
Importance: Low
Lets see,
Mounting Holes
Thru-holes for Dip IC's, resistors, capacitors, DO-35 diodes, Etc..
Thru-holes for DO-41 diodes, TO-220 packages, connectors with .025"
square post, Bridges.
Thru-holes for connectors with .045" square post, Euro Plug-in
Connectors, DO-201 diodes.
The occasional special part like Transformers, RJ11 Connectors, Mini-DIN
(PS2) connectors.....
Shall I go on?
Regards,
Steve Smith
Product Engineer ,
Staco Energy Products Co.
Web Site: www.stacoenergy.com
& www.stacopower.com
DISCLAIMER AND/OR CONFIDENTIALITY NOTICE:
This message, including any attached materials, is intended solely for
the use of the individual or entity to whom it is addressed and may
contain information that is privileged, confidential, and exempt from
disclosure under applicable law. If the reader of this electronic mail
transmission is not the intended recipient, you are hereby notified that
any dissemination, distribution, or copying of this communication is
strictly prohibited. If you have received this communication in error,
please e-mail or call Staco Energy Products Co. at (937) 253-1191. Thank
you for your cooperation.
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Smith, Richard
Sent: Friday, February 02, 2007 10:54 AM
To: [log in to unmask]
Subject: [TN] Tooling Hole Quantity
Folks,
Can you think of any (legitimate) reasons why more than 3 tooling holes
would be necessary on a PWB?
Thanks Much!
Rick
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
