As long as the flux doesn't burn off.
-----Original Message-----
From: Christopher Nash [mailto:[log in to unmask]]
Sent: Monday, January 08, 2007 9:36 PM
To: [log in to unmask]
Subject: Re: [TN] Reflowing different sized BGAs without exceeding
manufacturer's p eak body temperatures?
I may try to introduce a hot soak zone in order to get uniform heat. In
other words, have a 30-60 second soak zone in the reflow profile just below
the reflow temperature. This will allow for the board to heat up evenly
with the larger BGA temperatures catching up to the temperatures of the
smaller BGA's.
Christopher J. Nash
Mid-West Technical Support Engineer
Indium Corporation of America
www.indium.com
-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Macko, Joe @ IEC
Sent: Friday, January 05, 2007 7:21 PM
To: [log in to unmask]
Subject: [TN] Reflowing different sized BGAs without exceeding
manufacturer's p eak body temperatures?
Hello Fellow techs,
One of our CMs is having great difficulty developing a thermal profile for a
small, double sided, densely populated board with different sized BGAs on
one side. One of the BGAs is rather large and higher in thermal mass than
the surrounding smaller BGAs. The issue is that when he gets the solder ball
temperature of the larger BGA up to at least 205 C, the peak body
temperature of 2 adjacent but much smaller and thinner BGAs exceeds their
manufacturer's recommended peak body temperature of only 220 C by ~ 10 C.
The CM does not think he can make any more adjustments to the 9-heating zone
Heller oven to accomplish this task.
Does anyone have any suggestions/ideas on how to heat the larger BGA
sufficiently without over heating the smaller adjacent BGA components?.
Possibly, he can insulate the smaller BGAs with a piece(s) of tape on the
top (prior to assembly) to lower the body temperature - has anyone tried
this?
Look forward to reading anyone's idea. thanks
Joe
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
***This email, its content and any files transmitted with it are intended
solely for the addressee(s) and may be legally privileged and/or
confidential. If you are not the intended recipient please delete and
contact the sender by return and delete the material from any computer. Any
review, retransmission, dissemination or other use of, or taking of any
action in reliance upon, this information by persons or entities other than
the intended recipient is prohibited.
Messages sent via this medium may be subject to delays, non-delivery and
unauthorized alteration. This email has been prepared using information
believed by the author to be reliable and accurate, but Indium Corporation
makes no warranty as to accuracy or completeness. In particular, Indium
Corporation does not accept responsibility for changes made to this email
after it was sent. Any opinions or recommendations expressed herein are
solely those of the author. They may be subject to change without notice.***
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------
---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------
|
