Joel:
		Can you send a picture of the board design to Steve? He
may post it for everybody to see excatly the design of the board with
the mouse bites.
	Regards,
	Ramon


-----Original Message-----
From: TechNet [mailto:[log in to unmask]] On Behalf Of Eddie Rocha
Sent: Wednesday, January 24, 2007 11:50 AM
To: [log in to unmask]
Subject: Re: [TN] Question about cracker holes (panel breakaways)

The cracker holes should be designed so that the nubs (left after
breaking) do not protrude beyond the PCB dimensions. This means that
there will fall inside the board and leave a mousebite which can be
about .010 inch, if designed properly. Hope this helps.

-----Original Message-----
From: TechNet [mailto:[log in to unmask]]On Behalf Of Joel Alexander
Sent: Wednesday, January 24, 2007 7:04 AM
To: [log in to unmask]
Subject: [TN] Question about cracker holes (panel breakaways)


We have been using panels with internal breakaways for over 20 years.
There is a slight amount of material left when they are broken but we
have never had a customer complaint about this.

We have started doing military business and they are rejecting
everything because the cracker hole areas exceed print dimensions.  It
is obvious that the additional material at the cracker hole location
does not have any impact to the end use.

Is there any industry standard that would permit the use of cracker
holes

Also has anyone had similar experiences dealing with military customers
and if so what was the end result?



Joel Alexander

Quality Assurance Manager

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to
[log in to unmask]: SET Technet NOMAIL or (MAIL) To receive ONE mailing
per day of all the posts: send e-mail to
[log in to unmask]: SET Technet Digest
Search the archives of previous posts at:
http://listserv.ipc.org/archives Please visit IPC web site
http://www.ipc.org/contentpage.asp?Pageid=4.3.16
for additional information, or contact Keach Sasamori at [log in to unmask]
or 847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e To
unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet To temporarily halt or
(re-start) delivery of Technet send e-mail to [log in to unmask]: SET
Technet NOMAIL or (MAIL) To receive ONE mailing per day of all the
posts: send e-mail to [log in to unmask]: SET Technet Digest Search the
archives of previous posts at: http://listserv.ipc.org/archives Please
visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for
additional information, or contact Keach Sasamori at [log in to unmask] or
847-615-7100 ext.2815
-----------------------------------------------------

---------------------------------------------------
Technet Mail List provided as a service by IPC using LISTSERV 1.8e
To unsubscribe, send a message to [log in to unmask] with following text in
the BODY (NOT the subject field): SIGNOFF Technet
To temporarily halt or (re-start) delivery of Technet send e-mail to [log in to unmask]: SET Technet NOMAIL or (MAIL)
To receive ONE mailing per day of all the posts: send e-mail to [log in to unmask]: SET Technet Digest
Search the archives of previous posts at: http://listserv.ipc.org/archives
Please visit IPC web site http://www.ipc.org/contentpage.asp?Pageid=4.3.16 for additional information, or contact Keach Sasamori at [log in to unmask] or 847-615-7100 ext.2815
-----------------------------------------------------